Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Stuck Chuck Solution

Posts

Stuck Chuck Solution

#1

Stuck Chuck Solution

charlie belden

Having modified my JET Mini VS to add a reverse function, I had to then do something to keep my chuck from spinning off when I switched to reverse. And what I did was quick and easy - but stupid - LokTite. While it did keep the chuck from spinning off whenthe lathe is reversed - it also kept it from being removed when I wanted to switch chucks or use a drive center or face plate.

Lacking a spindle lock, and having the head stock collar with two holes in it for a tommy bar, holding the head stock fixed while using a wrench to get the chuck with adapter off works - unless - the adapter is LokTited to both the chuck AND the head stock thread. I bent my knock out bar trying to use it to keep the head stock shaft from rotating while using channel locks on the adapter. To make matters worse, there's not enough space between the head stock collar and the adapter to get an open end wrench on the adpater.

What I needed was something other than a tommy bar to hold the headstock collar fixed and an open end wrench that was thinner than normal open end wrench thickness. What I needed was a bicycle shop wrench for the adapters and a tool we in the U.S. often don't even know exists - a SPANNER.

Off to the nearest bicycle shop (we have lots of bicycle shops in the SF Bay Area because there are so many places to ride and so many types of riding options - road, mountain, cyclo cross, veledrome. Natuarlly, I needed a 38+mm open end flat wrench - and they only make 36 and 40 mm. But channel locks would do - IF I could hold the head stock collar securely.

There on the wall of bike tools was THE ANSWER - a Double End Bottom Brakcer Locking Ring Hook Spanner





With the head stock secured with the spanner, the heaviest set of jaws on the chuck opened to accomodate a 1/2" steel rod and a little elbow grease the adapter and chuck came free!

No more dropping chuck screws while removing them while the chuck is on the lathe, no more trying to find them in all the chips on the floor.

The spanner is a ParkTools HCW-5 and the best $17 tool I've bought in a long time.

Re: Stuck Chuck Solution

#2

Re: Stuck Chuck Solution

John Lucas

Charlie I'm surprised you had to go to those extremes for a Jet mini reverse. I added reverse to my Jet mini and never had any problems with the chuck coming loose. I instal the chuck by hand tightening. Then just use the chuck key and the knock out bar to lock the spindle and give the chuck one more little snug up using the keys as levers. Never had a problem.

Your solution however is a good one. I have been buying thin spanner wrenches like this whenever I find them at the Flea mkts. They are much better for releasing or locking chucks and spindles because they don't elongate the holes like straight rods will do. I've even made them. It takes a lot of cutting with a hacksaw and then careful filing but they aren't that hard to build if you want one bad enough.

Re: Stuck Chuck Solution

#3

Re: Stuck Chuck Solution

Hal Taylor

Hmmm...Wonder why it's called LokTite.

Re: Stuck Chuck Solution

#4

Steven Antonucci

Posted this a long time ago

steven antonucci

As a former bicycle mechanic, I have every tool in the kit to work on my bike... and I have even built a couple of pairs of wheels and trued them!

My bottom bracket wrench is attached to a magnet on the leg of my lathe. It was epoxied, but it kept coming off. How do you fix that? I put the magnet on the wrench and wrapped it in painter's tape...

Steve

Re: Stuck Chuck Solution

#5

Re: Stuck Chuck Solution

charlie belden

Lock implies UNlock. Tight implies Loosen. Both imply reversability

Welded or Fused on the other hand . . .

Re: Stuck Chuck Solution

#6

Dick Hines

Re: Posted this a long time ago

Dick Hines

I have reverse on both of my lathes and have never had the chuck unscrew. When I put the chuck on the spindle I laways give it a little snap the just as it gets up to the shoulder of the spindle. Works for me.

I don't use the grub screws that go in the spindle adapters. I forgot once and messed up a couple of the threads. When you are stupid you are suppose to suffer. :\

Re: Stuck Chuck Solution

#7

Re: Posted this a long time ago

Bill White

This post also proves that LocTite really DOES work.

Bill

Re: Stuck Chuck Solution

#8

Brad Vietje

Locktite Alternative

Brad Vietje

Late to the Party -- sorry.

While I would side with John that for most work that will fit on a mini or midi lathe, glue should not be needed if you have good clean mating surfaces (though the spanner wrench is also a great tool!), a good alternative to Locktite would be plain old CA glue, which most turners have at hand.

While CA is fairly shock sensitive, when flooded between mating threads, this should not be a huge issue. If you are doing something like coring dry burls in reverse, you're probably not using a mini lathe, and you really ought to use a chuck or faceplate with a grub screw.

A nice feature of CA is that it completely gives up the ghost when heated. Thus, if you had to glue on a chuck, just heat the chuck body or spindle shaft gently with a torch, and it will release.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Stuck Chuck Solution

#9

Loctite also realeases with heat


Re: Stuck Chuck Solution

#10

3 lbs of metal, Plastic Parts & Heat

charlie belden

The Super Nova 2 chuck in question weighs about 3 pounds - and has a plastic indexing plate on the back.

I tried a heat gun on the chuck but was concerned about the plastic indexing plate - and burning the lubricant on the moveable parts - thus making matters worse. Heating up the drive shaft would also pose a problem since Using a torch would have required cleaning up the whole area within 10 feet of my lathe - something I've successfully managed to avoid for years ; )

I was told that the real culprit was that I'd "bottomed out" the threads on both the outside threads of the adapter insert and the inside threads as well. A nylon washer or two would have prevented THAT contributing factor.

The solution to the Chuck Unwinding Phenomenon seems to be Set Screws. A little drilling, a little tapping and it's all reversable. The chuck comes set up for that, and even came with little rubber plugs so the set screw doesn't damage the threads.

Re: Stuck Chuck Solution

#11

Re: 3 lbs of metal, Plastic Parts & Heat

Carole Valentine

Don't count on the little rubber plugs preventing damage to the threads if you forget that the screw is in there and try to unscrew the chuck. DAMHIKT!