Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Quick-sharpening bandsaw blades

Posts

Quick-sharpening bandsaw blades

#1

Aage Rendalen

Quick-sharpening bandsaw blades

Aage Rendalen

Somebody mentioned a few years ago that they sharpened their bandsaw blades by running the blade in reverse, by hand, against a file. I decided the try it when my blade was getting dull--and much to my surprise it worked.

I used a diamond file, placed at a 45 degree or so against the blade and ran it a few rounds counter-clockwise. It did not--obviously--turn it into a new blade, but it allowed me to cut all the blanks I had left and then some before replacing the blade. I don't know how many times you can do it. I've tried it on two blades now, and on the last I must have resharpened it four-five times. I use a half inch blade with 3-4 tpi.

Whoever posted the tip, thanks.

Re: Quick-sharpening bandsaw blades

#2

barry rockwell

Re: Quick-sharpening bandsaw blades

Barry Rockwell

How the heck did you get your bandsaw to run backwards?

Re: Quick-sharpening bandsaw blades

#3

Steven Antonucci

Inquiring minds would like to know!

steven antonucci

First thought was to do it by hand...holding a file to a bandsaw under power sounds a little sketchy?

I have done it one tooth at a time with a Dremel on my old crapsman bandsaw, but the Rikon is 142" and I ain't that cheap...

Steve

Re: Quick-sharpening bandsaw blades

#4

Re: Inquiring minds would like to know!

john lucas

Simply unplug the bandsaw open one of the doors and crank it backwards by hand holding the diamond hone against the blade. Works but not as well as hand sharpening each tooth with the Dremel.

Re: Quick-sharpening bandsaw blades

#5

Re: Quick-sharpening bandsaw blades

robo hippy

I tried hand touch ups a couple of times, and it did a little. I do have a very good saw sharpening service that I take my blades to (Lennox bimetal), and they sharpen blades for a couple of dollars apiece. They do a much better job than I can even dream of.

I did find a hammock hook a few days ago, a couple of times in some apricot that I was turning. Slowed the blade down a tiny bit, but not nearly enough to stop it. That is one reason why I prefer the bimetal blades.

robo hippy

Re: Quick-sharpening bandsaw blades

#6

Lyle Jamieson

Re: Quick-sharpening bandsaw blades

Lyle Jamieson

Richard Raffan showed us the technique of sharpening the band saw blade by taking it off the band saw and lightly touching every tooth on the underside of the curf between each tooth on a standard grinder. He just used the side at the corner of the grinding wheel. There is no precision needed. Mine got sharper then it was new.

Re: Quick-sharpening bandsaw blades

#7

Re: Quick-sharpening bandsaw blades

eliot d

Any reason not to try the same thing on a table saw blade? I managed to run my BRAND NEW Forrest into (not through) a drywall screw! I kind of hate to send it back for sharpening already!

Re: Quick-sharpening bandsaw blades

#8

Lyle Jamieson

Re: Quick-sharpening bandsaw blades

Lyle Jamieson

Its worth a try unless it is a carbide tipped blade. We can not sharpen carbide well with a grinder.

Re: Quick-sharpening bandsaw blades

#9

Re: Quick-sharpening bandsaw blades

Bill Howatt

IMO, there may be something to be gained at relatively low risk by fooling with a bandsaw blade but to run the risk of ruining an expensive TS blade isn't worth it. Then there is the carbide issue which makes it a non-starter.

Bill

Re: Quick-sharpening bandsaw blades

#10

Re: Quick-sharpening bandsaw blades

eliot d

I suppose you're right. But I happen to have a diamond wheel. Do you think I would ruin the blade if I just touched up each tip?

Re: Quick-sharpening bandsaw blades

#11

Re: Quick-sharpening bandsaw blades

George Van Beynen

Careful Elliot or you may end up having to replace the carbide tooth if you screw up. This will be more expesive than a sharpening. ;)