Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Anyone 'made' Cole jaws and happy with them?

Posts

Anyone 'made' Cole jaws and happy with them?

#1

Anyone 'made' Cole jaws and happy with them?

Henry (Raleigh NC)

I have a Nova G3 chuck and want/need a better way to grip 'finished' bowls to turn the bottom.

Has anyone made Cole jaws that they actually use? Or do you break down in the end and just buy them?

Henry

Re: Anyone 'made' Cole jaws and happy with them?

#2

Re: Anyone 'made' Cole jaws and happy with them?

Bill Turpin in WNC mountains

My wife turns only small stuff. Usually less then 2" diameter. She had me make some rubber grippers to screw onto the holes that hold the jaws onto a small chuck. Using the center holes, she can grip already finished objects (less than 3/4" dia) that have already been finished. No scratches. This works good so that she doesn't have to use a Dremel, etc to clean off those little nubbins. Rubber corks from Lowes and some 4mm x 18/25mm flat head screws. I shortened the stoppers, drilled, and countersuck the heads on the lathe with a dreaded skew. Total less than $10. This will work with ANY lathe and any chuck. Adjust dimensions to fit our stuff.

Re: Anyone 'made' Cole jaws and happy with them?

#3

Ellis Walentine

We've had inquiries from all over... *LINK*

Ellis Walentine

..regarding our editor emeritus Garrett Lambert's Longworth Chuck article, and so far no complaints.

Ellis Walentine, Host


Garrett's Longworth Chuck Article

Re: Anyone 'made' Cole jaws and happy with them?

#4

Re: Anyone 'made' Cole jaws and happy with them?

Terry Scott

Id suggest making a longford chuck or get yourself a modern longford chuck http://www.coolhammers.com/longworth_chuck.htm

They work a treat

Re: Anyone 'made' Cole jaws and happy with them?

#5

Re: We've had inquiries from all over...

Henry (Raleigh NC)

Thanks Ellis.

I did a WC search before posting, and got through the first page or so of hits. I was not seeing anything related to making them and got impatient and posted my question. I have read this well done article before, but forgotten! In fact, that's likely where I got the idea that I could make them.

Thanks for the reminder.

Henry

Re: Anyone 'made' Cole jaws and happy with them?

#6

Re: Anyone 'made' Cole jaws and happy with them?

Dan Jechura Temperance Mich.

I did not make the "cole jaws" but I did make extentions for them so I could turn the bottom of 14" bowls. So far so good they are working.

Dan J.

Re: Anyone 'made' Cole jaws and happy with them?

#7

George Taylor

Re: Anyone 'made' Cole jaws and happy with them?

George Taylor

Ditto on the Longworth chuck; have the Cole jaws and haven't used them in the year I have had the Longworth chuck. In fact, I had thought of putting them up on the benefit auction. This thread just gave me the impetus to do it. Look for posting and pix this weekend.

George

Re: Anyone 'made' Cole jaws and happy with them?

#8

Re: Anyone 'made' Cole jaws and happy with them?

Ralph Lindberg

I did something similar (due to a suggestion from Dale Larson). I added 8/4 maple blocks to a Cole jaw set, and then cut a rim in at at (each) required diameter. I find the attachment more secure then the 8 points of the Cole Jaw

Which brings up another point, there are 4 point, 6 point and even 8 point "Longworth" designs out there, IMO the more points the better. I would not build (nor recommend) the 4 point.

Re: Anyone 'made' Cole jaws and happy with them?

#9

Re: Anyone 'made' Cole jaws and happy with them?

Barry Irby

I made a set years ago out of baltic birch plywood and they worked well. Eventually I bought a "real" set from Wood Craft. They will hold a bowl about ten inches in diameter. Then I made extensions for them so i can grip bowls up to 16". I really like the extension. Not sure I Still have the wooden ones but if I do, I would give them to you. They were fine, but I have moved on. They fit on the Nova chuck that uses the Tommy bars.

Re: Anyone 'made' Cole jaws and happy with them?

#10

ebd

Re: Anyone 'made' Cole jaws and happy with them?

ebd

I made multiple plywood jaws of any sizes I needed. I finally bought both large and small coles for my Axminster. I also had extensions made so that I could reverse to the max of my lathe.


Re: Anyone 'made' Cole jaws and happy with them?

#11

Steven Antonucci

Prepare for takeoff...


Re: Anyone 'made' Cole jaws and happy with them?

#12

Re: Anyone 'made' Cole jaws and happy with them? *LINK*

Fred Holder

I have accumulated considerable information on the Longworth Chuck on my web site at the below link. Lot's of photographs and text.


Longworth Chuck Information

Re: Anyone 'made' Cole jaws and happy with them?

#13

Thanks all; looks like a Longworth style it is...

Henry (Raleigh NC)

Looks to me like a Longworth style is may be marginally more complicated to make, but likely faster to use.

With the excellent links provided above, I believe I make one of those.

Thanks

Henry

Re: Anyone 'made' Cole jaws and happy with them?

#14

Re: Thanks all; looks like a Longworth style it is

Grant Wilkinson

Henry: I've made 3 different Longworth chucks. Until I got to the last one, with 8 buttons, I wasn't happy with them. With 8, it holds very well. As Ralph advised, I would stay away from the 4 button plans.