Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Bowl beginner...

Posts

Bowl beginner...

#1

Bowl beginner...

Scott in Douglassville

Hi, all -

So, I want to try bowl turning. Been reading Conover and Raffan books. Eager to get started. Only have spindle tools right now, so I want to buy a bowl gouge. Recommendations on size? I need a compromise size to start with: What's going to be the most practical size for all duty?

Chucks: Is it worth investing in a chuck now, or should I go with glue blocks and jam chucks for now. Is there a distinct increase in ease with a commercial chuck?

I'm still reading, so sorry if these are noob questions...

Thanks,

Scott

Re: Bowl beginner...

#2

To determing what size bowl gouge, ......

JamieDonaldson

...we need to know what size lathe and bowls you intend to turn. My go to gouge is the 5/8" deep flute, but for smaller work the 1/2" is better suited. Be aware that these are US measurements of the tool steel diameter, not the flute width as measured in European made tools.

Re: Bowl beginner...

#3

Re: Bowl beginner...

GaryG in MD

What Jamie said (and asked) is correct (of course!)

If you have a mini-lathe, get a 1/2" BG (bar size). Doug Thompson makes a nice one that I use all the time.

If you have a 12" or larger lathe get an Ellsworth Signature BG (5/8" steel) and one of his sharpening jigs. It is a "universal" tool that you can't go wrong with.

...Gary

Re: Bowl beginner...

#4

Steven Antonucci

Is your goal to make bowls or cut bowls?

steven antonucci

If you own a scraper, you can make a bowl. If you do not, you can buy a scaper of any type and make bowls.

If you want to make a bowl with a bowl gouge, I think 1/2" or 5/8" is the way to go. I have a smaller bowl gouge, but I rarely use it.

A glue block or a face plate is a good starting point.

Steve

Re: Bowl beginner...

#5

Re: Bowl beginner...

robo hippy

For basic bowl turning, I would recommend 3 basic tools. One round nose scraper, and 2 gouges. You need one gouge with about a 40 degree bevel for cutting the outside, and the inside walls, and a gouge with about a 60 degree bevel for going from the wall through the transition, and across the bottom. The scraper can also clean up the bottom, but you get a better finish cut with the gouge, at least when you learn how to use it properly. The scraper is good for general clean up work when the gouge is not cutting smooth, and the surface looks more like a washboard. This cut is made at a shear angle rather than flat on the tool rest.

Chucks are a great convenience, a bit on the expensive side, but faster to use than jamb chucks and waste blocks.

robo hippy

Re: Bowl beginner...

#6

Re: Bowl beginner...

John Lucas

I use my 1/2" bowl gouge for almost everything from 20 bowls down to tiny stuff. For beginner I would recommend a 1/2" bowl gouge, and a thick round nose scraper.

You could use just a Hunter Hercules tool to turn bowls. It will do both the inside and outside as well as some more advanced techniques. You can also use the flat and round EZ woodtools. The advantages of these tools is that you don't need to sharpen them. I still prefer a bowl gouge because I think it's a more all around usefull tool and you said you have other tools which tells me you probably have a way to sharpen.

You don't need a chuck. It does speed things up and I know a lot of turners are impatient but I turned for a lot of years using faceplates, waste blocks, glue blocks and jam chucks to turn all sorts of things. I was probably 10 years into turning before I owned my first chuck.

Re: Bowl beginner...

#7

Re: Bowl beginner...

jim 9 miles

Good info above on gouges

I have turning 30 years and do not own a chuck. Just have to be a little creative, learn to glue, and plan ahead.

Re: Bowl beginner...

#8

Re: Bowl beginner...

Jim Breeden

Scott,

There is no such thing as a noob question - I'm living proof! :D

Re: Bowl beginner...

#9

JL

Re: Bowl beginner...

JL

I'll argue for a chuck.

You can get a small WoodRiver chuck from Woodcraft for $99. You can also get a Teknatool SuperNova 2 for $140 (through 4/27) from Woodcraft.

A chuck gives you a lot of versatility. Yes, you can use a jamb chuck and face plates - but a good four jaw chuck makes thing so much easier.

Re: Bowl beginner...

#11

Re: Bowl beginner...

Terry Scott

Scott go to our club web site www.sawg.org.nz

some great info to be had

The book the Beginners Guide is what we teach people to turn with

We start everyone off with 2 x 10mm bowl gouges one sharpened at 35% and one at 55degrees

All you need but be warned you will become a tool junky soon enough l.o.l

Buy good quality tools as they will be high speed steel the older sorby type are carbon steel and dont or wont hold an edge

Feel free to drop me an email if you need help with anything

Cheers

Re: Bowl beginner...

#12

Re: To determing what size bowl gouge, ......

Scott in Douglassville

Jamie, my Delta 46-700 (I think that's the model) swings 12", so that's my max, but honestly, I'm looking smaller than that for now. So I'm guessing 5/8"?

Re: Bowl beginner...

#13

Scott, for that lathe, which I owned,....

JamieDonaldson

...about 5 lathes ago, the 1/2" will do just fine. I believe any bowl turner would benefit by owning both a 1/2" and 5/8" as a working pair, and those are 2 of my basic set of the first 5 tools that every bowl turner should buy.

Re: Bowl beginner...

#14

Re: Bowl beginner...

Scott in Douglassville

Thanks for the link, Terry! Lots to learn there.

I'm a borderline tool junkie/GAS attack fool to begin with, which is why I lean toward getting a chuck now while I have the dosh. All my tools are Packard, and so far I've been happy.

Scott

Re: Bowl beginner...

#15

Re: Bowl beginner...

Scott in Douglassville

Thanks for the input. I'm leaning toward an Axminster from Lee Valley right now, though I have no clue which jaw set I'd buy...

Re: Bowl beginner...

#16

Re: Scott, for that lathe, which I owned,....

Scott in Douglassville

Thanks, Jamie. I may pick your brain about grinds and profiles as I go, too!