Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Took me a minute...

Posts

Took me a minute...

#1

Steven Antonucci

Took me a minute...

steven antonucci

to figure this out. Enjoy:


There will always be someone with less than you...

Steve

Re: Took me a minute...

#2

Re: Took me a minute...

Curt Stivison

I guess you don't have to worry about what speed to set your lathe on.

Re: Took me a minute...

#3

what speed to you turn at-3450

john lucas

that's pretty cool. Hope he doesn't make anything large.

Re: Took me a minute...

#4

I don't recognize what he used to......

JamieDonaldson

..make the tailstock quill?

Re: Took me a minute...

#5

Almost looks like an arbor to make a buffer.


Re: Took me a minute...

#6

Steven Antonucci

make sure not to use the handwheel

steven antonucci

What I can't fathom is that he turns for 4 minutes at 3450 and only removes that tiny little bit of wood. I bet he wears a faceshield (and earplugs!)

Steve

Re: Took me a minute...

#7

Re: make sure not to use the handwheel

Lynn Taylor

I think he is turning on the wrong side of the lathe and, therefore, the piece is turning backwards!

Re: Took me a minute...

#8

Nope-that end of the grinder would turn correctly


Re: Took me a minute...

#9

Steven Antonucci

It is not a lathe

steven antonucci

look closely, and you will see that his headstock is a grinder that he's rigged up to spin the wood, and frighteningly fast for his level of ability I might add...

The grinder is rotating towards him, so in this case, he's on the right side... although I would suggest that there is no right side in this set-up.

Steve

Re: Took me a minute...

#10

I need to rig up a photo of my first lathe

john lucas

I was building a cabinet and wanted to turn some knobs. I mounted my drill on my workbench with a band clamp to hold the on switch. I made a wooden tool rest that was clamped to the workbench. Put the blank on a screw that was stuck in the jacobs chuck and grabbed my sharpest screwdriver and made a couple of knobs.

Re: Took me a minute...

#11

Dick Hines

Re: I need to rig up a photo of my first lathe

Dick Hines

Holly ****!! When the video started I ran to the shop for my face shield.

Re: Took me a minute...

#12

Speed roughing won't happen when.....

JamieDonaldson

...he's using a skew as a negative rake scraper!

Re: Took me a minute...

#13

Mike Stafford

I have for so long....

Mike Stafford

done so much with so little I can now do almost anything with nothing......

Re: Took me a minute...

#14

Rob Wallace

Re: I have for so long....

Rob Wallace

"Never was so much owed by so many to so few..."

British Prime Minister Winston Churchill

20 August 1940.

Re: Took me a minute...

#15

Re: make sure not to use the handwheel

R Payne

Is he turning at 3450 or 1725?

That isn't that different from what I learned on. Only I didn't have the hand wheel. I inherited what is best described as a motor with a drive spur and a dead center on the far end. The motor was old enough to have oil ports and was single speed at 1725 rpm. I stopped using it when the wiring started sparking when I turned it on.

ron

Re: Took me a minute...

#16

Looked like a bench chisel to me!


Re: Took me a minute...

#17

Re: Took me a minute...

Terry Scott

Ive been telling you that a skew is the best scraper I have (grin)

Was that a washing machine in the background

Painful to watch when with a skew cut that could have been cut in seconds