Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Problems with Vicmarc VL300

Posts

Problems with Vicmarc VL300

#1

Problems with Vicmarc VL300

gtwilkins

I haven’t used the lathe for a couple of months but it was working perfectly the last time I shut it off and unplugged it. The lathe has a Fuji FVR-E11 220 Single phase VFD.

Now when I plug it in I have no sign of life, the LCD display remains dark.

So far I have checked:

Voltage to the lathe and to the main switch on the inverter panel is good.

Removed main switch and tested with ohm meter, appears good.

However when I test the voltage across the switch with the switch off, with the lathe plugged in I have voltage on both terminals of the switch.

Has anyone experienced anything similar or any ideas how to further troubleshoot this problem.

I can’t find a reset unless it is inside the VFD

Thanks Trevor

Re: Problems with Vicmarc VL300

#2

Mike Stafford

Re: Problems with Vicmarc VL300

Mike Stafford

My lathe has two power switches- one for regular use and the other is a kill switch that does not permit power to the regular on/off/variable speed switch. The main kill switch on my lathe is pull on push off.

Any chance you have a main kill switch that has not been turned on?

Re: Problems with Vicmarc VL300

#3

Re: Problems with Vicmarc VL300

gtwilkins

Mike,

It's the main power switch that I am testing, I have the Australian model with the main power switch on the inverter panel.

Big problem is I phoned Australia and there is no-one there to help until next week!

Trevor

Re: Problems with Vicmarc VL300

#4

Mike Stafford

Re: Problems with Vicmarc VL300

Mike Stafford

Ahhh... sorry I can't help. My electrical knowledge is about as limited as my knowledge about women...... ;)

Re: Problems with Vicmarc VL300

#5

Re: Problems with Vicmarc VL300

Galen Vetterick

Not familiar with the control but in the past have you unplug it for two months and not lost programming? Is there a reset to a basic program if you loose power for that period?

When you say you tested the switch in the off position and had power to both terminals. Was this tested by meter probes connected to each switch terminal Or testing each terminal to a neutral? Testing across the switch in off positon will show voltage as you are going from one hot side to the other being nuetral.

Your meter is measuring the potential across the switch.

If you are testing each switch terminal to a seperate ground or neutral then there is something providing feedback power and would not appear correct.

Do you have the manual with a trouble shooting guide? Any resetable overlaods, fuses or fuse wire links? I hope you can get a better answer than my simple comments.

Re: Problems with Vicmarc VL300

#6

Re: Problem sorted

gtwilkins

Mike and Galen,

Dhuh, Whap, (that's the sound of me slapping myself upside of the head) and my wife is still shaking her head.

The problem was caused by the adjustable idiot in charge of the lathe!!

I had installed a couple of new circuits in the basement for my wife's fabric business as I had a cold enforced break from turning and like a right muppet I had moved the lathe breaker and landed it on the same block so it had only one phase. Of course when I pulled the new breakers to test the double for the lathe I put the lathe breaker back in the correct spot and got two phases again.

Surprise, surprise the lathe works just fine when you feed it right power.

Trevor

Re: Problems with Vicmarc VL300

#7

The first law of troubleshooting is........

JamieDonaldson

...to always check the simple things first! :D

Re: Problems with Vicmarc VL300

#8

Re: "my wife is still shaking her head"

Galen Vetterick

So you made a mistake.

Everybody does that.

BUT WHY ON EARTH WOULD YOU INFORM YOUR WIFE ABOUT IT???????????

That's not a mistake that's just plain crazy! :D

Re: Problems with Vicmarc VL300

#9

Re: The first law of troubleshooting is........

John Lucas

When I worked for Xerox I can't tell you how many times I went to a repair and found the machine unpugged.

Re: Problems with Vicmarc VL300

#10

Re: "my wife is still shaking her head"

gtwilkins

Galen,

Worse than the head shaking have been the comments since I returned from the shed:

Lathe still working dear?

It’s a good job you didn’t electrocute yourself!

Don’t try to fix anything else!

I actually thought I might even get the “it’s a wonder you didn’t loose an eye”

With hindsight I could have just said “I dunno it just started working again” and wandered off, well live and learn.

Trevor

Re: Problems with Vicmarc VL300

#11

George Taylor

Re: The first law of troubleshooting is........

George Taylor

And after you check the plug, ask yourself what was the last thing you did on the machine and work back in time. When chasing outages in my day job, human intervention is so much more the cause of problems than equipment failure.

George

Re: Problems with Vicmarc VL300

#12

Brad Vietje

Lost Opportunity!

Brad Vietje

You had a perfect opportunity to look like a genius who reasoned out the problem, and fixed the situation. I'd probably leave out the detail of the breaker position, and give yourself credit for being so darned smart that even these hi-tech devices are well within your reach!

Now, about your electric panel..... wouldn't a 2-pole breaker always contact two phases? I work in service panels from time to time, and usually the two 120 legs in the panel reach alternating slots, no? Are you using two single-pole breakers, or one 2-pole? I'm a bit confused about how the movement of the breaker would do this.

Safe spinning (and wiring),

Brad Vietje

Newbury, VT

Re: Problems with Vicmarc VL300

#13

Mike Stafford

Re: Lost Opportunity!

Mike Stafford

Brad, this sounds like a brilliant strategy but with wives who have seen us fail to correctly coordinate the colors of our clothes it will not work. They have learned to sift through all the male BS and see us for what we truly are....incredibly handsome, intelligent and gifted husbands....... :D

Reminds me of my favorite joke...

After 50 years of marriage, a husband and wife came for counseling. When asked what the problem was, the wife went into a tirade listing every problem they had ever had in the years they had been married. On and on and on: neglect, lack of intimacy, emptiness, loneliness, feeling unloved and unlovable, an entire laundry list of unmet needs she had endured.

Finally, after allowing this for a sufficient length of time, the therapist got up, walked around the desk and after asking the wife to stand, he embraced and kissed her long and passionately as her husband watched - with a raised eyebrow.

The woman shut up and quietly sat down as though in a daze.

The therapist turned to the husband and said, "This is what your wife needs at least 3 times a week. Can you do this?"

"Well, I can drop her off here on Mondays and Fridays, but on Wednesdays, I go bowling."

Re: Problems with Vicmarc VL300

#14

Re: Lost Opportunity!

gtwilkins

Brad,

I am using a double breaker but on the older panels, this is a Federal Pioneer that's 40 years old, it is possible to just get the one phase. I believe the on the newer panels you can't do it as they alternate.

Trevor