Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Bead sanding ... How do you

Posts

Bead sanding ... How do you

#1

Bead sanding ... How do you

Rich Pearson in Mill Creek, WA

Having purchased some bead making chisels in various sizes and experimenting with cutting beads, the next question involving technique is....how do you sand those little devils?

I'm practicing on some spalted alder firewood, so I do get some tear out...I suspect that a less punky wood wiill help with that.

Is there a technique, particular material or sanding product which you have found to be effective in doing a good job sanding while still preserving the half-round profile?

Re: Bead sanding ... How do you

#2

Re: Bead sanding ... How do you

John Lucas

I had hoped to have time to do my beading video this weekend but that didn't happen. To start with start the cut with the beading tool below center. Enter the wood at a moderately steep angle. Then push the handle down which lifts the cutting edge into the wood. This gives more of a shear cut for the sides of the bead. The top of the bead will still be a scraping cut so take it really light. I do 2 or three lifts pushing the tool in a little further each time.

I prefer to turn my beads with a detail gouge. The top is cleaner but of course you need to practice a lot to be able to turn a lot of beads the same size.

Sanding. That's a tough one. Remember the 2 beaded perfume bottles I did. The first one had flat beads. I had to sand too much to get rid of the chip out on the top surface of the beads. I fold the sandpaper in half to create a tight edge and then sand from the deepest part toward the top. I try not to touch the top any more than absolutely necessary. I sand all the left sides at once re-folding the paper as needed. Then do alll the right sides.

Sometimes this technique leaves a rounded area between the beads. If this happens I go back with the toe of the skew and "tuck it in" as the guy who taught me beads used to say. I just push the toe in to make a really clean line between the two beads if this is what I want.

Re: Bead sanding ... How do you

#3

Steven Antonucci

Thompson detail gouge

steven antonucci

I've found the best way for getting consistent beads is to use my homemade beading tool (any piece of steel with a half round profile in it) to get my sizes all the same and using it as a negative rake scraper. Once the are all the same size, I recut the with a detail gouge to get sanding free surfaces.

Like John, I use the long point on the skew if I need a sharp line between beads.

Steve

Re: Bead sanding ... How do you

#4

Mike Stafford

Re: Bead sanding ... How do you

Mike Stafford

When I want to delineate the valley between the beads I use my long point tool. Similar to a regular point tool I just ground the the 3 bevels about an inch long. I hone the facets with a diamond stone and the sharp point and razor sharp edges allow me to clean up the beads if need be.

It is similar to a Drozda Vortex tool I guess but I have never seen one of those. I stumbled upon it when I was taking a class with Ed Moore. I kept sharpening the facets too long on a point tool he was teaching us to use and finally gave up and put the tool away. Then one day I decided to try it for cleaning up some beads and it worked like a champ. Since then it has been part of my regular tool line up.

Re: Bead sanding ... How do you

#5

A very sharp tool

Jorge

I have no experience with a beading tool. I made beads for years with a skew and of late, I am making them with a small spindle gouge really sharp or with a detail gouge. I don't see the need of sanding, the sharp edge leaves a nice surface, not quite as burnished as with the skew, but very clean.