Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

tailstock photos

Posts

tailstock photos

#1

tailstock photos

darrin hill


tailstock and quill


back of keeper plate above slot. Set screw holds in place from the right. U can see the burrs and the grind...

sorry,, should have added these to the previous thread.. but it's 2:13am and the twins are making me loose sleep... Trying to figure out what happened and how to avoid it... yes.. i read the threads.. just wanted to show photos.



the shiny bit after grinding down the burrs.. u can see how much it had..


closeup of quill.. u can see the slope of the grind..


and purple highlights of what should be there..

enjoy

Re: tailstock photos

#2

Re: tailstock photos

walta

We may never know if you needed the extra leverage because the hand wheel / keeper had a defect or if the extra leverage allowed you push hard enough to cause the damage.

I feel the threads on my DVR tail stock are ruff making the hand wheel difficult to turn.

The tail stock of the new 20 inch DVR are very different and finely machined.

Walta

Re: tailstock photos

#3

Retail Stock photos

Barry Irby

Walta, the threads on my DVR felt rough also. I mentioned it to the owner of the local WoodCraft where I bought the lathe (probably ten years ago) and he advised removing the keeper and the quill and hand wheel and cleaning everything and reassembling it with graphite or some other dry lube. The dry lube does not collect dust as readily. I did it and it made a huge difference.

Darrin, you have obviously worn off the shoulder on the handwheel. I doubt there is any fix other than to replace the wheel and the keeper. You need to look inside the tailstock and see if it is also damaged. You may need a whole new tailstock. Might contact NOVA's repair center and see if they have one they will sell you cheap. Keep the quill clean and the thrust plate well seated.

Re: tailstock photos

#4

Re: tailstock photos

Carole Valentine

That looks to me like your keeper plate was not seated properly to begin with, causing the wear. Although I can't imagine using the TS when there was enough friction to cause that amount of steel removal! Spurred by this thread, I just went out and did some maintenance on mine and checked it out. Never did it in the 7 years I have had the lathe! LOL Everything was fine. One thing I did notice is that if you simply drop the plate back in the slot and tighten it down, it may be a bit out of alignment, even though it is "in the slot". By moving the plate just a hair this way and that while slowly winding in and out I could find a sweet spot and then tighten it down.

Re: tailstock photos

#5

Re: tailstock photos

john lucas

Looks to me like they need to put a thin hardened washer between the mating parts that push together when drilling or loading the tailstock. Maybe that would reduce the wear.

Re: tailstock photos

#6

Re: tailstock photos

Jim Breeden

Darrin - How did you get the keeper out of the tail? When I originally received my DVR, I disassembled the tail stock/quil and cleaned all the evil smelling Chinese grease off everything. Read the instructions very carefully, and still could not get the keeper out of the slot, and grease is still packed in there. The quill did seem rough at first, but after cleaning it real good, and lubing with dry lube, it seems to be doing ok. I was wanting to clean it out so as not to get the evil greasyness on something. :b

Re: tailstock photos

#7

Re: tailstock photos

Carole Valentine

Jim,

Look in the handwheel end of the tailstock...you will see a small hole in the casting. You will have to rotate the handwheel until you see the set screw in the hole. Loosen it, then use a small flat blade screwdriver or something similar in the slot to lift the keeper out.

Re: tailstock photos

#8

Keith Tompkins

Re: tailstock photos

Keith Tompkins

Darrin, that should be an easy fix...take the worn part to any competent machinist, who can weld up the worn area,then remachine it to original specs. You can purchase new shims, or he can machine new ones as well. That design will require regular oil lubrication, a ball-bearing thrust bearing would be far superior, but much more expensive to fabricate. Probably not worth the effort unless you have your own machine shop.

Re: tailstock photos

#9

Re: tailstock photos

Jim Breeden

Carole

I tried that, but it wouldn't budge, so I quit. Didn't want to damage anything.

Re: tailstock photos

#10

Re: tailstock photos

darrin hill

if you can't get that screw loose, that/s why your keeperplate won't come out.. it holds the plate in place..

Re: tailstock photos

#11

Re: tailstock photos

john lopez

As a longtime fellow Nova user this thread reminds me to clean & spray my MTs & tailstock as well.

If I was facing a rebuild or replace dilemma with mine I would consider the swing away tailstock option as an expensive but sensible upgrade.

That tailstock didn't seem heavy when when I bought it.