Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Berger hollowing tool

Posts

Berger hollowing tool

#1

Berger hollowing tool

Brian McInturff

So I'm going through some of the tools I have but don't use and I find a Soren Berger hollowing tool that I had picked up cheap several years ago. So now to the questions.

1. What's the easiest way to sharpen and do you sharpen the end? Better to just buy the sharpening jig?

2. Is the tool strictly for going center out on the bottom of boxes?

3 what position do you can't it to?

4. How do you use it correctly? lol

Thanks

Re: Berger hollowing tool

#2

Re: Berger hollowing tool *LINK*

Juergen

Here's a link to a video of Soren making a Lamp Shade with the tool


Watch Soren use the tool

Re: Berger hollowing tool

#3

Re: Berger hollowing tool

mjonesrdg

I use the Berger tool a lot. I didn't "get it" when I first got it and it spent a lot of time in a drawer, but with a bit of playing around, I've found it to be quite versatile. I seldom take it to the grinder and just hone the edge lightly with a diamond card all the way around the rounded end. The cut is from center toward rim, and will cut from the bottom up, pulling, or from the top down, pushing. With green wood and hollow forms, I present the full cutter and pull wide streams of ribbon shavings out. It "hogs" out material faster than any other cutter in my arsenal. Present the cutter so that a smaller, (forward part) edge makes contact and you can make smaller cuts. Turn the cutter down (by rotating the handle) and make real light cuts and pull "angel hair" shavings. Especial good for straight sides of boxes and open vase forms. Mounted in a heavy bar, I get excellent control even at the bottoms of deep (12")forms.

Re: Berger hollowing tool

#4

Re: Berger hollowing tool

jim 9 miles

Use it a good bit. Mine sat in the drawer a long time also. There is somewhat of a learning curve before you feel like it does any good. Agree with comments above. Think of it kind of like a gouge turned side ways. Rub the bevel and turn it up slightly to start cutting as you would a gouge.

Re: Berger hollowing tool

#5

Re: Berger hollowing tool

Terry Scott

Brain Not because I sell the tool and are the Nz Agent

But I think these are one of the best end grain box tool on the market.I only sell what I use and can put through the Terry Scott "if I cannot break it no one can test" (I admit I find the Hunter tool on a par)

I use mine or I should say more than one

Every time I turn a box

1. What's the easiest way to sharpen and do you sharpen the end? Better to just buy the sharpening jig?

Just use a diamond hone bring the hone up to the bevel of the tool and a couple of swipes and shes good to go

Only use the sharpener if you need to reshape the tip due to a mishap with hitting something or dropping on the floor

My tips are 4 or 5 years old and with the diamond hone will last a while yet '

Using the jig is a bit of a knack and more lucky you will alter the tip so much its shot (from experience )

2. Is the tool strictly for going center out on the bottom of boxes? I say yes pre-drill to the depth you want to finish at draw across center out you are rubbing the bevel not scraping across the end grain .

When you come up the side of the wall turn the tool to the side bevel and draw out.I can cut the end grain on the bottom of a box so smooth I sand wet 1200 and then its finished

3 what position do you can't it to?

Under cutting I change to my Hunter bent tool after watching Mike Stafford On the Norway cruise the light bulb came on that I hadn't been rubbing the bevel enough when under cutting

4. How do you use it correctly? lol

Rub the bevel .The cutting area is right on the curve of the tip

Ive seen the tip placed in a big boring bar but there was no control at keeping on the bevel so it became a scraper

If you email me I can send the instruction sheet

Only to happy to walk you through the tools correct use

Or go to my web site and you can copy and paste from there.

Cheers

Re: Berger hollowing tool

#6

Mike Stafford

Re: Berger hollowing tool

Mike Stafford

Terry sent me a Berger tool more than a couple of years ago and I had difficulty finding its sweet spot. But as luck would have it Soren Berger was in the vendor area of a symposium I attended and I was able to get a hands on demonstration with the man himself.

Once Soren showed me how to use the tool I found it very useful for cleaning up straight sided boxes with flat interior bottoms. I still rough hollow the inside with a gouge as I have never gotten used to pre-drilling the center. After rough hollowing I use the same procedure Terry describes to clean up the interior.

I can do almost the same thing with my #3 or #5 Hunter straight tools but they will leave a radiused corner where the bottom meets the side. The Berger tool will leave a pretty sharp corner.

I sharpen the Berger with a diamond hone. Terry sent me a sheet from Soren explaining how to to that and I have yet to put the tip on the grinder. You can cut a lot of wood just by honing with a diamond.

I actually have the tool in both sizes and I use the small one for small straight sided/flat bottomed boxes and I use the larger one for, as you might guess, larger and deeper straight sided/flat bottomed boxes.

Re: Berger hollowing tool

#7

Re: Berger hollowing tool

Brian McInturff

Terry, not sure how to find your email address. I'd very much like the instructions. my email is philatelist at earthlink dot net

Thanks

Re: Berger hollowing tool

#8

Re: Berger hollowing tool

Brian McInturff

Seems like a tool I need to learn to use. thanks for all the detailed advice.

I remember playing with it when I recieved it but it seemed dull and I didn't have a clue on how to sharpen it.

There are 2 sizes? How do I determine which size I have and does someone carry both sizes. Packard only list one size and Soren doesn't list anything but the threader on his site now.

With Mikes article in Woodturning Design and my wife just recently asking about making some trinket/jewelry boxes then timing on this seems appropriate for me!

Re: Berger hollowing tool

#9

Re:  email address and spare tips

Terry Scott

Hi Brain the email is displayed at the top of the page beside the name of the person posting

timberly@xtra.co.nz

Had a few enquires for spare tips

Just got in some more if anyone is buying my Dvd I can slip one in the same bag

Many buy just the tip and ad to their own shaft

cheers

Re: Berger hollowing tool

#10

Re:  email address and spare tips

Brian McInturff

Hmm, for some reason the email addresses don't show up on mine. Maybe an iPad issue?