Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Great Bandsaw tip in this video

Posts

Great Bandsaw tip in this video

#1

Steven Antonucci

Great Bandsaw tip in this video

steven antonucci

If you watch the video, watch how he only cuts one of the two pieces flat. It will be obvious why when he gets to the bandsaw part.


Steve

Re: Great Bandsaw tip in this video

#2

Mike Stafford

Re: Great Bandsaw tip in this video

Mike Stafford

I know the video action is speeded up but Glenn Lucas turns a bowl that quickly.

Never thought about using the cut offs to cradle the round side of the blank. I made angled supports from rough stock that I had..... Doh!

Re: Great Bandsaw tip in this video

#3

Re: Great Bandsaw tip in this video

Jim Breeden

Fascinating! :O Question: How did he get that polished finish with only the sander?

Re: Great Bandsaw tip in this video

#4

Dick Hines

Re: Great Bandsaw tip in this video

dick hines

Why even cut the blank round. Just put it between centers and use a bowl gouge to do the work. I can't remember the last log I cut into a round blank.

Re: Great Bandsaw tip in this video

#5

Re: Great Bandsaw tip in this video

Carole Valentine

Why doesn't he cut it round with the larger flat side down so everything is supported? What am I missing here?

And what kind of lathe its that? The motor is so close to the work.

Re: Great Bandsaw tip in this video

#6

Re: Great Bandsaw tip in this video

Jennifer Indy.USA

I'm thinking the same thing? Use the larger flat side down and use a circle template. And if you must use just the small flat side cut with the chain saw, I'm assuming so you can draw a full circle on the cut side, why not cut both sides with a flat and then cut the log in half and not mess with the little craddle pieces? He also needs to cut a V in his chain sawing stump. His little blocks aren't helping much.

Just my observations.....

Re: Great Bandsaw tip in this video

#7

Re: Great Bandsaw tip in this video

clay foster

Why not cut a flat on both halves instead of messing around with those cradle cutoffs? If he cut a V notch in the top of the stump, the log would be a lot more stable than those loose boards he's trying to hold the log between.

Re: Great Bandsaw tip in this video

#8

Re: Great Bandsaw tip in this video

Jim Breeden

Maybe Steve is trying to tell us something? 8)

Re: Great Bandsaw tip in this video

#9

Re: Great Bandsaw tip in this video

john lucas

I agree with Jennifer. Although the wedges seem to work all it takes is once for it to slip and you could hurt your self. I prefer to put the big side down and use my templates.

Re: Great Bandsaw tip in this video

#10

Re: Great Bandsaw tip in this video

Bill White

Dang! I thought that I was the only feller who turned that fast. I'm busted.

Bill :D

Re: Great Bandsaw tip in this video

#11

Steven Antonucci

I seriously think it's a good tip.

steven antonucci

I didn't post this as a "wow, look at what he's doing" type of video.

I thought it was a good tip.

If you've ever cut a rounded blank without support, you quickly learn how dangerous it is (and get good at changing your blade).

Why might I leave the rounded side? I may want the sapwood to be an accent on a cherry/walnut turning. I may want a natural edge. Cutting away the corners may make it fit over the lathe and seeing the bottom may help me visualize the thing I am making better.

Nope, I just thought it was a good time. No subtext...

Steve

Re: Great Bandsaw tip in this video

#12

Brad Vietje

Even BETTER Band-Saw Tip

Brad Vietje

Cut with the big side DOWN!!!!!!

It drives me freakin' crazy seeing people push an unsupported chunk of wood into a running bandsaw. That's just too risky to be considered smart -- even with the small flat that he prepared with the chain saw.

Supporting the upper edge with a wedge of wood is better, but those first few cuts could spell disaster - why do it?

I made up a series of wooden discs from 6" to 12" in diameter, which can be tacked to the smaller face (or round bark surface) of a billet, and all one needs to do is select the best size template, tap it in place with a nail, and cut around it. For bigger than 12" I cut the corners off with the chain saw, and round it up on the lathe.

I've seen some pretty violent bandsaw "accidents", and I can assure you, most accidents happen because someone failed to prevent them. Doing something overtly stupid just raises the chances of a Darwin Award.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Great Bandsaw tip in this video

#13

Mike Stafford

Re: Great Bandsaw tip in this video

Mike Stafford

If it is important to you with regard to how the grain is centered in the bowl it makes sense to round up your blank with that surface up so that you can see what you are doing. I use a circle template centered on the grain pattern I hope to have inside the bowl with the flat side up. Then I use my wedges to keep the blank from tipping as I saw off the waste.

I don't believe the gentleman in the video had any concerns about the grain alignment.

If the grain alignment is unimportant then by all means put the flat side down and use a circle template. Or even better just mount between centers or on a screw and turn the darn corners off with your bowl gouge. Wait, someone already said that.

Re: Great Bandsaw tip in this video

#14

Brad Vietje

Slight Variation...

Brad Vietje

I usually round the blank on the lathe with a bowl gouge, mostly because I'm not trying to pay the bills through turning, so a little lost time isn't costing me income. When I use the bandsaw, I always cut with the big face down, and cut out the largest diameter that I can.

In either case, I then turn the bowl between centers so I can balance the figure, sapwood, etc... before committing to a tenon or a screw chuck.

So I'd say even if you are taking care to balance the appearance of the bowl, its still possible to cut the circles wide side down (bark up) for greater stability and safety, and rough turn between centers.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Great Bandsaw tip in this video

#15

Re: Even BETTER Band-Saw Tip

John Lucas

Right you are. And accidents on the bandsaw happen with lightening speed. I've had one close call. Well it probably wasn't that close because I always keep my hands out of the way as much as possible. However the catch was really violent and if I had my hands close I could have lost something before I could blink my eye.

I think what happened was the wood was not totally flat on the bottom and as I rotated it around it suddenly rocked to the unsupported side and pulled the wood over jamming the blade. I keep my hands as far to the left and right as possible and never inline with the blade. That save me I'm sure but did scare me.

I now check the wood more closely and will hot glue a wedge under it if necessary.

Re: Great Bandsaw tip in this video

#16

Mike Stafford

Respect the band saw!

Mike Stafford

As my dear departed friend Ed Moore so frequently advised after he had his band saw accident, "RESPECT THE BAND SAW!"

Re: Great Bandsaw tip in this video

#17

I hear that echo as well Mike.

:(

Re: Great Bandsaw tip in this video

#18

Me 2, just before I push that green button


Re: Great Bandsaw tip in this video

#19

Keith Tompkins

Re: Even BETTER Band-Saw Tip *LINK*

Keith Tompkins

Here's a link to a bandsaw safety article I wrote for American Woodturner Magazine. Think twice before emulating the bandsaw technique shown in the video. Unsupported cuts are the most frequent cause of horrific bandsaw accidents...totally preventable accidents, I might add.


http://www.keithptompkins.com/storage/bandsawsafety.pdf