Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Tubing for sphere turning?

Posts

Tubing for sphere turning?

#1

Tubing for sphere turning?

Tony - Memphis

Just wondering what sort of tubing might be good to sharpen up and cut spheres with? Haven't tried it yet, but it is a technique I've erad about and been meaning to try. I noticed a lot of tubing is welded and has a seam that might mess things up. I looked at EMT and regular tubing in the hobby rack at Lowes yesterday.

Thanks,

Tony

Re: Tubing for sphere turning?

#2

Re: Tubing for sphere turning?

john lucas

I've read where people grind the teeth off of a hole saw. I tried it with some pipe I had and didn't think it came out that well.

Re: Tubing for sphere turning?

#3

Re: Tubing for sphere turning?

R Henrickson

My brother did a couple for me, since he has access to a metal lathe. He tried taking the teeth off a hole saw. At best, the process frustrated him, and the result was useless. He also turned a taper onto the end of a piece of 2" inside diameter black iron gas pipe. That was reasonably successful, though 1 1/2" I.D. would probably be more useful (I was working on a sphere just over 3" in diameter).

Re: Tubing for sphere turning?

#4

Keith Tompkins

Re: Tubing for sphere turning?

Keith Tompkins

Hi Tony, that's how I did this piece; I used a piece of steel tube, ground and honed on the outside, honed on the inside as well. Hope this helps.

Re: Tubing for sphere turning?

#5

what nose angle?

GaryG in MD

Keith, I've tried it with black pipe and not been very satisfied.

I suspect the nose angle has a lot to do with success/failure.

I've decided that a very "blunt" angle (like the kind you use to go across the bottom of a bowl) might work better than a "sharp" angle.

What are your thoughts?

(And why, given all your tools, did you use it on that beautiful wood?)

...Gary

Re: Tubing for sphere turning?

#6

Keith Tompkins

Re: what nose angle?

Keith Tompkins

Hi Gary, I should have clarified...I used the hollow pipe to turn the spheres I used as a finial...they are all 1/4" diameter. I sharpened the pipe with a long bevel, perhaps 40-45 degrees. Each sphere was then drilled, and supported with guitar string.

Re: Tubing for sphere turning?

#7

arch punch

Dave Staeheli

I've been using an "arch punch". Good steel and perfectly round, which hole saws are not. Initially you can use it without modification, but then I just rub the cutting edge against a diamond hone. Yes, it flattens the edge, but creates a new edge with the flattened edge and the inside bevel. Remember, it is the inside edge that does the cutting on a sphere. A bit pricy though, especially in the larger sizes.

Re: Tubing for sphere turning?

#8

tricky!


Re: Tubing for sphere turning?

#9

Re: Tubing for sphere turning?

Fred Holder


Several year ago when I started making the Chinese Balls, I made a swinging jig out of plywood as shown in the photograph. I used this for several years and then began using ones made from metal. The swinging portion was made of three layers of 3/8 inch quality plywood, with the center piece 3/8 inch below the top of the other two. A piece on top had a screw hole to lock the tool in place.

The swinging jig makes the best spheres that one can make.

Re: Tubing for sphere turning?

#10

Mike Stafford

Re: Tubing for sphere turning?

Mike Stafford

This is a jig that Arne Sortland built and posted which he uses to create spheres. He uses a Hunter carbide cutter on the business end.


Re: Tubing for sphere turning?

#11

Re: Tubing for sphere turning?

Fred Holder

On both of my current jigs: One by Vermec in Australia and one from Fred Lindsay in the United States. I use Hunter Carbide cutters on both of them with great results. It is hard to beat the Hunter Carbide cutters for any purpose.