Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Nova DVR Riser Blocks

Posts

Nova DVR Riser Blocks

#1

Bob Moffett

Nova DVR Riser Blocks

Bob Moffett

I have a Nova DVR and would like to increase the swing from 16" to 20" or 24" inches. Does anyone know of a source for riser blocks for the DVR? What is the address that I can go to to buy a reconditioned DVR? Thanks in advance

Re: Nova DVR Riser Blocks

#2

Alan Zenreich

Re: Nova DVR Riser Blocks

Alan Zenreich

http://www.novatoolsusa.com/Reconditioned-Products_c10.htm

NovaToolsUSA has a reconditioned DVR XP for $1700

Woodcraft has new DVR XP units on sale right now for $1900

http://www.woodcraft.com/Product/2005485/22172/Nova-DVR-XP-Lathe.aspx

They are selling the new DVR 2024 for $3000

Re: Nova DVR Riser Blocks

#4

Steven Antonucci

You'd need to swap most of the lathe

steven antonucci

If you had 2" risers, you'd have to get a banjo riser, or a really long tool rest post to make up the difference. The cam nut that holds the pivot would also need to be longer by 2". And your tailstock would be too low without a riser.

Not a simple upgrade...

Steve

Nova 3000 user since 2000... and I've had my lathe in pieces numerous times.

Re: Nova DVR Riser Blocks

#5

Mike Stafford

Re: Nova DVR Riser Blocks

Mike Stafford

Bob, just bite the bullet and spend some of that moldy old money you have and buy a new lathe. I recommend getting a Robust or a Stubby.

Lan will help you move it......

Re: Nova DVR Riser Blocks

#6

Re: Nova DVR Riser Blocks

John Lucas

Bob I've never heard of anyone making riser blocks for the DVR. I have done it for an older lathe and it's a lot of work. It requires a riser for the headstock and tailstock. Then requires extensions for the bolts that lock them down. Then you need a custom tool rest with longer post. I built my risers out of MDF and then added all the extra bolts. A lot of work and unless you make the risers out of steel you will have some flex and vibration.

Re: Nova DVR Riser Blocks

#7

Rotate the head

Jorge

I am assuming that the DVR has the same rotate the head capability of the Nova 3000, I did make a number of over 16" bowls and platters out board, Had to improvise a tool rest, but it was not that hard and did the job.

A lot simpler than making several raising blocks.

Re: Nova DVR Riser Blocks

#8

Re: Nova DVR Riser Blocks

Lan Brady

Mike,

I done told him the same thing. Thanks!!!

Lan

Re: Nova DVR Riser Blocks

#9

Re: Rotate the head

Henry (Raleigh, NC)

Same experience as Jorge.

I only did one this way - but I did a 20" shallow bowl on a Nova 3000 by rotating the head, improvising support for the tool rest, living with some vibration, and sanding a lot more than I like to.

Henry

Re: Nova DVR Riser Blocks

#10

Re: Rotate the head

John Lucas

Ditto what they said. I bought the outrigger support for my Nova 3000 but it vibrated too much so I rigged up a piece of all-thread rod with nuts to go from the floor to the tool rest to steady it.

The large platter I did required that I remove the blank in order to reposition the tool rest to clean up the back side. It was not the best way to go which is why I saved my money and bought the Powermatic 3520A.

Re: Nova DVR Riser Blocks

#11

Amen to that!

Jorge

I did same thing, except I got the PM 3520 b.

It is a total compatibility between the Nova 3000 tool rests, chuck adapters faceplates etc. they all fit the PM 3520 b. Not so with a Oneway...

Re: Nova DVR Riser Blocks

#12

Bob Moffett

Re: Amen to that!

Bob Moffett

Thanks for all the good suggestions. From the comments, I gather that I didn't have such a great idea, but Mike, why would I want a Stubby boat anchor? lol