Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Big improvement...little money...?

Posts

Big improvement...little money...?

#1

Big improvement...little money...?

mjonesrdg

UHMW self-adhesive tape, applied to my took rests....wow!

I'm sure that tools such as the parting tools with sharp edges will abuse this material and create the very problems that I'm trying to eliminate. No question in my mind, however, when working gouges. this smooth, consistent, slippy-slidey, surface is gonna help heaps. and it's cheap enough to replace every week if necessary. No more filing, sanding, and polishing to resurface a dinged tool rest surface.

And then...(drum roll here)...I applied the same stuff to the bottom slides of my banjo. WooHoo! my banjo is like a shuttlecock! Just a little push will send it sliding to the opposite end of the ways.

I have no idea how long this tape is going to hold up under regular use, but it's value even as a temporary assist will be big for me. Woodcraft, Rockler, Amazon...all priced around $8.00 for 60 inches of it.

Hopefully, a little nugget to y'all

Mike Jones in Redding Ca

Re: Big improvement...little money...?

#2

I just wax the tool rest.

John Lucas

I learned a long time ago to use wax on my hand planes to make them glide across the wood. I keep an old candle handy and just run it across the tool rest. Also work wonders on my captured bar secondary tool rest.

Re: Big improvement...little money...?

#3

interesting...

GaryG in MD

That's interesting, Mike. Let us know how it holds up.

Your tools shouldn't be marking your rest. You note "sharp edges" on a parting tool. The first thing I do when I get any new, non-round tool is to grind all the sharp bottom corners off to make nice, smooth quarter rounds. THAT will stop your tools from sticking on the rest, and you probably won't need the tape.

I agree with John -- I keep an old candle stub handy and use it as needed.

Your comment about using it on the banjo is also interesting. My concern would be that the tool rest might be able to vibrate under load because of the added soft cushion. That could cause waves. Have you experienced any such problems?

...Gary

Re: Big improvement...little money...?

#4

Re: interesting...

mjonesrdg

Gary, I run a PM 3520A and use a tool rest that I got from John Lucas several years ago. The Powematic tool rest is of a bit softer material. I don't treat any of my stuff particularly rough, but I've had to file, sand , and polish the rests occasionally as they get rough just from daily use. Usually this is no big deal, but when I want to make those delicate angel hair cuts while fairing a curve or finishing off some tear-out, it bugs me to no end when the tool hits a rough spot just at the most inopportune time.

The ways get treated from time to time as well, and for pretty much the same reasons (I do get lots of glue, sealer, wet shavings etc. on the ways) but no real "rough use" damage. The underside of the banjo never did exhibit the prettiest machining, and the cast material never did ride on a perfectly flat, nicely machined, surface.

The Slick Tape on the tool rest may not prove, in the long run, to be a huge benefit, but I will always have some on hand now for those special operations.

Candle wax, I think would be stickier, and attract dust and other boogers, thus exasperating the loss of smooth tool control that I want.

On the banjo bottom, I have the most hope for a long term assist/improvement. The whole thing rides and clamps just as steady with the tape as without. but it moves up and down the ways with one hand and no muscle.

If you try it, I think you'll like it.

Mike Jones, in Redding, Ca

Re: Big improvement...little money...?

#5

Re: interesting...

John Lucas

The candle wax does not attract dust at all and it's not sticky. It is like a wonder drug. You do have to re apply it often because it does wear off.

My Powermatic tool rest is soft also and I have rounded the edges of all my tools. When I teach at other places I often have to file their tool rests to get a good smooth surface. Haven't dinged my Robust or Bestwoodtools tool rests yet. I guess they are harder.

Re: Big improvement...little money...?

#6

Re: Big improvement...little money...?

Phil Powell

Ive used candle wax and bees wax and carnauba wax and others on my lathe bed and tool rests, but I'm now using a different solution. Don Geiger used to sell a spray called Ballistol Lube, don't know if he still

Does but it can be bought at a gun shop. The stuff is amazing. I spray it on the lathe bed, use a piece of

4-0 steel wool and rub lightly to remove the oxidation then wipe clean. At that point my lathe ways are

As slick as snot on a door knob. Best stuff ever! I bought a can several years ago an still have some left.

Re: Big improvement...little money...?

#7

Re: Big improvement...little money...?

eliotandmax

Yes, but would you believe that David Ellsworth advocates purposefully wetting the lathe bed so it will rust making the banjo hold better! I told him once that I just couldn't get my self to do it! But there you have it.

Re: Big improvement...little money...?

#8

Re: Big improvement...little money...?

eliotandmax

What I do is file occasionally and follow up with a high speed wire wheel. Smooth as ice even without wax. It's a good idea , too, to just keep just about any kind of sandpaper handy and regularly sand the rest a little.