Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Undulations: Controlled Burn

Posts

Undulations: Controlled Burn

#1

Undulations: Controlled Burn

charlie belden

Turners spend a great deal of time either sanding, or developing turning techniques, to produce as perfectly smooth surface on pieces as they can. Often the wood surface is made even smoother by applying a glossy finish. The result can be stunning - and shiny. And that can be a good thing.

But if the resulting piece looks like it might be glass or porcelin or plastic, and the wood becomes lost . . . ?

So turners use piercing and pyrography, carving and texturing, dyes and stains, to change the surface look of the piece - and remove most or all of the impact of the wood, and the nature of of the wood.

One of the qualities of the nature of wood is that it's a grown medium. It literally grows on trees, or rather in them. As a result, it has growth rings. And it doesn't always grow at a fixed rate, or symetrically.

In the winter it grows slowly- and the wood added is dense. In the spring its growth rate increases rapidly to support budding leaves and branches. Slow growth - dense wood Fast growth - less dense wood.

So how can this harder/softer wood quality be exploited?

One way is to sand blast it - abrading away the softer wood more than the harder wood to hopefully add an interesting texture to a piece. And areas can be protected from abrasion, with masks and frisket. IF you have a sand blaster, this is one means of exploiting the harder/softer wood quality.

Another way is to use FIRE - soft wood burns faster than hardwood. Propane torches are readily available and inexpensive. There are even small "pencil flame" torches that can give you more burn control, allowing you to even write or draw on a piece.

But there are other means of controlling how much wood is burned away - and where - by controlling what areas are exposed to the torch flame.

These two examples are of redwood fence boards. They were layed flat, noiyo pebbles placed on them where I wanted the wood protected and a propane torch was taken to the wood. A wire brush removed the charring and the process was repeated. The result was an undulating surface of contours, small islands separated by water of different depths, wind and water carved mesas rising above ancient rivers bedsand flood planes.



That's pretty crude at turning scale, but there's a method that traditional Japanese cutting tools makers have been using for half a millenniaor more - to heat treat and heat color metal - CLAY. Clay is a heat insulator. As a paint or paste, it can be aplied, thicker for more insulation / protection from heat, thinner when less insulation / protection from heat is desired.

You can pick up "kiln wash" a refractory material that comes as a fine powder from ceramic supply outfits. Mix it with water, or better yet alcohol if you're in a hurry, paint in on, let it dry, add more and so on. When dry, get out your propane torch and do some experimenting. Woods with wider growth rings with hard winter wood and softer spring wood could produce some interesting fire carved surfaces,

Re: Undulations: Controlled Burn

#2

Steven Antonucci

I do this in ash (no mud involved)

steven antonucci

Burn and wire brush. Leave the wood thicker, or you run the risk of burning through it. If you get an ember, do NOT try to blow it out. Blowing on it only makes it burn more...DAMHIKT.

S

Re: Undulations: Controlled Burn

#3

Re: I do this in ash (no mud involved)

charlie belden

Think in terms of airbrushing.

Soft edges freehanding is quick and spontaneous - but you'd better have a good idea of where you're going - and how you'll get there. And there's color overlapping and overspray. Not a big deal when working large. Gets to be more and more of a problem when working small - and maybe complicated. Masked airbrushing takes more forethought and up front time and effort, but you don't have to be so careful when doing the actual airbrushing.

This "insulator masking" idea can provide an element of control when scortching and burning, allowing for harder "edges" and more detail. It could be used to kick up the "contrast" between soft and hard grain and maybe even permit "undercutting", something not easily done, or done at all freehanding. It also allows you to see, and keep seeing, your pattern as you torch the wood. Pencil lines are hard to impossible to see when a flame is on or near them - and they burn off very quickly, being carbon already. Clay, on the other hand, stays visible and won't burn off.

Imagine a piece with a spiral pattern "carved" with fire, a geometric pattern carved in it with fire. And imagine that the carving, rather than being soft with rounded edges, is crisper and maybe even undercut, providing shadow lines to add to the effect. Or maybe the harder grain is "painted" and the piece torched, the softer grain "carved" - thus literally Popping The Grain - raising the harder grain (actually lowering the softer grain) and using the grain this way as a design element.

On the right piece, with the right wood, this burn masking could have some interesting possibilities.