Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Handwheel

Posts

Handwheel

#1

Handwheel

Jim Rutten

I bought a handwheel hub from oneway several months ago and am finally starting to think about creating one but have some questions. First, on the faceplate side, for some reason there is a section that stands proud of the flat faceplate. My guess is that you are supposed to drill the hole to the diameter of this piece such that the outside of the piece is flush against the wood. Does that seem right to you? What kind of wood would you use to make your handwheel? What diameter would you make it? How thick would you make it (I have turned on lathes with pretty thick handwheels and I like them that way, but I am not sure if it is anything besides pleasing to my big hands)? Given that they will become permanent, what kind of screws would you use? Anything else I am forgetting?

Re: Handwheel

#2

Re: Handwheel

Wally Dickerman

You're right, the part that stands proud is to center the hub. You mount the hub, then turn the handwheel. Most any wood will do but it should have the same density throughout so that it balances well. I've turned several handwheels for my lathes over the years. My Oneway handwheel is 7.5 inches in dia. and is fairly thick. It is contoured to give a comfortable grip. You might like one even larger. I had a 9 incher on my Nichols lathe. I happened to have a very pretty piece of box elder on hand so that's what I used. I used short pan head screws.

Be sure to lock the handwheel on with the setscrew provided, in case you put the lathe in reverse

Re: Handwheel

#3

Re: Handwheel

Wally Dickerman

I should mention that I first mounted the handwheel block on a 4 inch faceplate with short screws. I bored a hole through the handwheel on the lathe, contoured it and mounted the hub. After reversing it and mounting it on the hub I countoured the front, turning away the screw holes

Re: Handwheel

#4

Steven Antonucci

Size matters

steven antonucci

I have a Nova 3000... and the motor moves to change the pulley. If I made a bigger handwheel, it would interfere with the motor movement for that pulley change. In addition, it creates a huge problem if the handwheel and motor are close and you get a finger in the wrong the place. DAMHIKT

Steve

Re: Handwheel

#5

Re: Handwheel

HeatherAinAK

I took a class with Stewart Mortimer. We used club members lathes and one person kept having trouble with vibration. He took the beautiful turned handwheel off the lathe and the problem was gone. He suggested that most any wood has enough density differences to cause a problem and that MDF makes the best if not prettiest handwheel

Heather

Re: Handwheel

#6

Harry Robinette

Re: Handwheel

Harry Robinette

I use a 6" round of Coreon counter top material on my General, smooth but easy to use and don't hurt the hand.

Re: Handwheel

#7

Re: Handwheel

Wally Dickerman in Arizona

I wouldn't argue with Stuart Mortimer but I've had several wood handwheels and they all worked very well. I'll agree that the wood must be chosen carefully. I can crank my lathe up to 4000 rpm with no vibration at all.

A friend made a fancy segmented handwheel. Worked well until he cranked his lathe up to well over 3000 rpm. Good thing he was out of the line of fire!!

Re: Handwheel

#8

Brian McKearney

Re: Handwheel

Brian McKearney

Here's a pic of the handwheel that I made for my Oneway. It is 1 3/4" thick and 7 1/2" diameter. Made from maple with a slight depression on both sides. I also turned a recess in which the hub that I purchased from Oneway is mounted with short screws to hold it in place.

Brian


Re: Handwheel

#9

Re: Handwheel

Tommy Holmes

I just got a secondhand Oneway 2436. I was thinking about using a tap to thread a wooden handwheel rather than buying the hub. Will this work?

Re: Handwheel

#10

Re: Handwheel

Wally Dickerman in Arizona

Won't work....The spindle locking knob will be in the way. The hub that Oneway provides gets the handwheel 2 inches away from the headstock. Some folks have tried a 6 inch faceplate as a handwheel. The locking knob becomes a knuckle buster. Also, the hub has a setscrew to lock the handwheel to the spindle for reverse turning.

Re: Handwheel

#11

Re: Handwheel

Tommy Holmes

Thanks, Wally.