Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Does your head stock line up

Posts

Does your head stock line up

#1

Does your head stock line up

Terry Scott

I was emailed today and was asked to post my pour attempt at an article as many on wc dont look at wow and with the number of responses maybe of interest

Here goes

Does your head stock line up

Before I start using any lathe I always check if the head stock lines up with the tailstock

especially when I am doing my winged vessels as when I flip the work over I have to have the piece running true or the wings end up differnt thicknesses.

Have you found when remounting a lid on a box for example that when you bring up the tail stock the live center cuts in a figure of eight.

Or flips the lid out of the jamb chuck.

Finials are hard to get right as you end up with of center turning at the point

Many turners that Ive asked have had no idea if their lathe is in alignment or not, they just think it should be.

I havnt found a swivel head lathe yet that locks back in line correctly.

Even on my stubby 1000 I was surprised that it was out (turned out id bolted it down and racked the frame. Yes I laid the floor

Ive been trying to find an article on aligning the head stock and tail stock without success.

So Ill give it a go Please add to this if you see anything I have missed

This article is also on my web site www.timberlywoodturning.co.nz

Thanks to Dick Veitch for the pictures

This is how I go about it and know carry a Acruline with me when I travel

I have no association with Nova but have found this system the best method

Happy to learn of other methods you may use

Nova Acruline Lathe Alignment System

DOUBLE ENDED No2 MORSE TAPER

This item is designed to be fitted into the NOVA lathe's tailstock and headstock spindles to bring back the alignment for those lathes with adjustable tailstocks or headstocks.

Many turners tell me they are having trouble turning certain items because they have problems lining up their lathe's headstock and tailstock.

The Acruline is what you need.

Are you finding that you are having trouble drilling straight, or that when you bring the tailstock up to your work the live centre forces the work to one side or cuts a figure of eight in the work?

Bringing up the two points of your spur centre and drive centre is not accurate as one mm out will cause a whipping action on longer spindle work; or both the head and tail may be out of line but still meeting at these points.

To use the Acruline:

1. Loosen the headstock so it rotates freely

2. Place the Acruline firmly in the tailstock

3. Bring the tail stock up so the tip of the Acuruline is just inside the opening of the head stock spindle

4. Lock the tailstock to the bed

5. Wind in the quill with the hand wheel until the morse taper seats firmly into the head stock

6. Tighten the headstock

7. Remove the Acruline

You can further check the headstock alignment by holding a long bit of wood in a chuck.

Do not bring the tailstock into contact with this wood.

Then rotate the wood gently and make a pencil mark at the centre of rotation at the tailstock end of the wood. Bring the tailstock with a live centre in it close to the pencil mark and check the alignment. This assumes that the tailstock is correctly aligned and checks headstock alignment only.

Bringing up the tail stock and headstock with spur and drive is not very accurate as the tapered points play tricks on the eyes.

Remember being 1mm out when the tail stock and head stock are brought together means 10mm out over a meter of bed.

Cheers

Terry

Re: Does your head stock line up

#2

Great advice, Terry!

GaryG in MD

Thanks for the heads up on this.

You're right -- I think we often ignore the possibility of misalignments.

It's a very good thing to MAKE it right, and your procedure is simple and well advised.

Thanks for putting it here on WC too. I look at the pix on WoW, but not the messages, so I would have missed it. (Note to self...) ;-)

...Gary

Re: Does your head stock line up

#3

Re: Does your head stock line up

Hal Taylor

Thanks Terry. Now you've got my interest up and am curious to see if my lathe is close to true.

Re: Does your head stock line up

#4

Dale Jablonski

Re: Does your head stock line up

dale jablonski

Terry, I've been aligning my DVR pretty much by eye. Where can I find one of these alignment tools?

Re: Does your head stock line up

#5

Re: Does your head stock line up

Carole Valentine

A Google will take you to Teknatool for the Acruline. A Google for "Morse taper alignment tool" will give you other options.

Re: Does your head stock line up

#6

Re: Does your head stock line up

Jim Breeden

Terry - thanks for the alignment info. I've seen that tool at the Nova web site.

I have noticed when I line up the dead and live center on my DVR they are off a smidgen. You've convinced me to get one. With all of us out here with a swivel head lathe, are you going to get a commission? Hope so. :D

Re: Does your head stock line up

#7

Mike Mills

Re: Does your head stock line up

Mike Mills

Good info and food for thought.

Just playing devil’s advocate…

In step 5…. Wind in the quill…. Won’t there be play in the quill with it loosened to wind it?

Maybe they need to add a 5.1 Tighten the quill.

I can see where if the item is firmly fixed in the headstock, the distance will increases (to 10mm?) over a meters length. But it seems, if the work piece is marked in the center it will be off the same 1mm no matter what the distance if held between points. Both “points” are still off only 1mm.

Re: Does your head stock line up

#8

Steven Antonucci

Doesn't solve the racked bed issue?

steven antonucci

I own one and use it it to realign my headstock and tailstock, but it is only a few inches long, so I don't think it would help if you had a long twist in the ways? You cannot use it with the tailstock at the end of the bed.

I know that mine is a little bit off because I see it when I flip end to end. Someday, when I have nothing to do, I may have a friend who is a machinist come over and do a proper level on it. The double taper is a no brainer for pivoting headstocks, but there is enough slop in the tailstock to make it something I'd use every time that I needed precision, even if the headstock hadn't moved. I am debating shimming my tailstock too...right after I level the ways :)