Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Semi OT-Beer Tap Threads

Posts

Semi OT-Beer Tap Threads

#1

Semi OT-Beer Tap Threads

Don Orr

Does anyone know what the standard threads are for a beer tap? I want to turn a tap handle for my nephew and want it to thread on easily. I don't go to bars much. Might have to just visit one and take my pitch gauge and do some measurements. Any ideas for a metal thread insert source?

Thanks.

Re: Semi OT-Beer Tap Threads

#2

Re: Semi OT-Beer Tap Threads

Dave Long

There's a pretty story in the Oct. 2011 American Woodturner about Mark Supik in Baltimore who has a company which makes beer taps. There might be something in that article which would help. Their website is marksupikco.com which has a lot of information on tap handles and contact information.

Re: Semi OT-Beer Tap Threads

#3

yes, Mark Supik is the one to ask...

GaryG in MD

He's in our club and a great guy.

He'll tell you everything you need to know. ...Gary

Re: Semi OT-Beer Tap Threads

#4

BTDT

Mark Mandell - Gone Round In Jersey

Did one for a friend's bar. Instead of tapping the wood, I drilled the blank with a 3/4" hole before turning the handle to take a 3/8x16 coupling nut which was then set into the handle with epoxy when finished. Fine adjustment of the handle's orientation (family coat of arms) was done with a couple of thin brass shim washers.



The ferrule is a section of a chrome sink tail piece.

Several other friends have asked for one. They're fun to do, and a reliable source of free beer. :D

Re: Semi OT-Beer Tap Threads

#5

Re: BTDT

Harold

http://www.kegworks.com/threaded-fitting-for-draft-beer-faucet-tap-handles-855-p173188

Link to tap handle nut.


img

Re: Semi OT-Beer Tap Threads

#6

Re: Semi OT-Beer Tap Threads

Nelson

Got some yesterday from Woodcraft, 3/8 brass inserts part # 11m30 $7.50 for 10.

Re: Semi OT-Beer Tap Threads

#7

Re: Semi OT-Beer Tap Threads

Harold

Kegworks lists the thread as 3/8 x 16

The woodcraft part number specified is 3/8 x 24. To match Kegworkds the part number should be 11M40.

Re: Semi OT-Beer Tap Threads

#8

Re: Semi OT-Beer Tap Threads

Nelson

You are right it is 11m40,tried it before I left the store. My bad.

Re: Semi OT-Beer Tap Threads

#9

Thanks!

Don Orr

I knew I could count on the braintrust here!

I forgot about the article on Mark Supik-great suggestion.

Re: Semi OT-Beer Tap Threads

#10

Ken Vaughan

Beer Tap Threads - may depend on Customer

Ken Vaughan

Don -- the advise above is good, but the construciton may depend on the customers specs.

I did a run of commemorative tap handles for Alaskan Brewing this fall and they wanted a stainless steel shank into the handle. I drilled and epoxied 3/8 by 16 stainless steel all thread rod about 11 inches into the handle leaving a stub for commercial threaded fittings at the bottom -- which mounted to the 3/8 by 16 threads on the top of the taps.

Re: Semi OT-Beer Tap Threads

#11

Brad Vietje

Re: BTDT

Brad Vietje

These appear to be the kind that are inserted by threading them onto a bolt with a stop-nut, then removing the nut and bolt -- is that correct?

I made some tap handles for a soda fountain a few months ago, and the inserts supplied by the tap manufacturer were the kind with a slot on one end for insertion with a big standard screwdriver. These were not acceptable, tended to break (needed larger hole???), and were difficult to insert nice and straight. I ended up turning solid wood pieces with no brass adapter, and used a thread cutter to thread the wood (pretty hard species), and reinforce the threads with CA. I think the inserts at the link above look better than what I tried.

Safe spinning,

Brad Vietje

Newbury, VT