Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Oneway control question

Posts

Oneway control question

#1

Oneway control question

Randy L

Hi first post here. I have a question regarding the control box on the Oneway lathe. If one wanted to extend the length of the arm that holds the control box could one cut and splice in an extra length of wires leading to the box? Any kind of special wiring or something else specific to the machine that prevents making mods. I know about the remote that is available but I'd like to make the factory equipped arm longer.

Re: Oneway control question

#2

Re: Oneway control question

steve worcester

If you are talking about the wired remote, with the two buttons, yes you can splice it and extend it. That would likely be easier than a new wire.

It is low voltage, probably 18 gauge.

Re: Oneway control question

#3

Lyle Jamieson

Re: Oneway control question

Lyle Jamieson

Dont know about the wires but I think the revolving arm is a bad idea. The revolving arm is a pain and is always in the way. When I work on a Oneway I put the arm on the back side of the lathe and leave it behind the headstock and use the remote on-off mounted on the side of the bed on the tailstock end. Its safer to have the on-off in a fixed position and on the tailstock end. Now the revolving arm in no longer in the way. This adaptation does not need longer wires.

Re: Oneway control question

#4

Re: Oneway control question

Lewis Dodd

Like wise! this helps inadvertantly hitting or bumping the varible speed control . which always seemed to be in the increase speed direction, that can get your adrenalin pumping! At first I used to have to put a big rubber band around mine.

Re: Oneway control question

#5

Re: Oneway control question

Randy L

I'm working on the outboard side of the headstock and would like to extend the arm to reach that position.

Re: Oneway control question

#6

Re: Oneway control question

john lucas

I would call Oneway and get the answer from the guys who designed the machine. They seem to be incredibly willing to help folks out.

Re: Oneway control question

#7

Re: Oneway control question

Randy L

Thanks, seems that's what I'll do.

Re: Oneway control question

#8

Re: Oneway control question

Barbara Gill

Randy, I have the remote on/off that has a magnetic attachment. That is what I use for outboard turning. It might be easier and less expensive than extending the arm.

Re: Oneway control question

#9

Re: Oneway control question

Randy L

How do you control speed?

Re: Oneway control question

#10

Re: Oneway control question

John McAlevey------WebKitFormBoundaryvjFovdc+Khof1

I removed the swinging pendant arm, rerouted the wiring and mounted the control box on a piece of half inch plywood. I put a 2 inch magnet on the plywood and now I can move the box anywhere I want. For me it is a much better arrangement than the swinging pendant which I found was always in the way. In order to keep the wiring straight I took pictures of it before I began the job.

Re: Oneway control question

#11

Re: Oneway control question

Randy L

You've made this my DUH question! I'm off to look into that right now. Thanks John!

Re: Oneway control question

#12

Re: Oneway control question

Barbara Gill

I adjust it before turning it on, bring it up to what I feel is appropriate, then walk to the end of the lathe.

Re: Oneway control question

#13

Re: Oneway control question

steve worcester

Take the speed controller knob off and put a piece of neoprene underneath it. Adds friction to the dial and just a little more difficult to bump speed.

Re: Oneway control question

#14

Re: Oneway control question

John McAlevey------WebKitFormBoundaryvjFovdc+Khof1

Randy- I can try to post a picture of my set-up if you'd like to see it.

Re: Oneway control question

#15

Re: Oneway control question

Randy L

No need John. I meant that after reading your reply I thought, "Duh now why didn't I think of that". I'm in the process of doing what you described.

Re: Oneway control question

#16

Re: Oneway control question

Randy L

I've been doing that, but prefer to have all of the controls near at hand.

Re: Oneway control question

#17

Keith Tompkins

Re: Oneway control question

Keith Tompkins

HI Steve, I was going to post that idea yesterday.. ;)

Re: Oneway control question

#18

THANK YOU John!!!

Randy L

What a simple solution. After opening the control box I was surprised at the number of wires, so followed your suggestion and took photos, also wrote down where each wire attached. Your suggestion eliminated any need for the existing arm as well as eliminated any possible reason to purchase a remote box. I can now place the factory control box wherever I like. So obvious but I never thought of it. Thanks very much!