Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Grinder Vac

Posts

Grinder Vac

#1

Grinder Vac

John Lucas

OK got it done. Now to figure out how to run a test. I think I'll put some fine saw dust in there. I don't ever plan to have any sawdust in there but there is a foam filter. If you had saw dust packed in the filter that could be a pretty good test.

Re: Grinder Vac

#2

Re: Grinder Vac

Nick Tuzzolino

Thanks for the photo, John. I have a similar setup, but yours is more practical and a lot better. Thanks for an idea to make mine better.

Re: Grinder Vac

#3

Dick Hines

Re: Grinder Vac

dick hines

Yep. but it could also start a fire in your vac.

Re: Grinder Vac

#4

Steve Kubien

That would be my concern.

Steve Kubien

I would think simply channeling the metal dust (and sparks) through the tubing and into a steel bucket would do the job. The dust has got to be pretty heavy to be airborne for long. Heck, a coffee can would suffice.

John, are you making this more complicated than it needs to be? Am I blowing smoke out of my, ummmm, digestive tract?

Re: Grinder Vac

#5

Re: That would be my concern.

Don Evans

If you run it into a closed cavity you'll immediately get back pressure and nothing more will go into it.

I'll try to post pix of mine tomorrow, I'm doing the same thing except with 4" hoses and my old delta dust collector. I removed the bags however and the collector is piped outside. It doesn't run long enough at the time to be concerned with lost heat or AC from the shop.

Before doing this I got tons of little metal particles and dust from white wheels. My setup reduced that by 99 percent. I can tell by table top of the grinder stand and how clean it now stays.

Don

Re: Grinder Vac

#6

Keith Tompkins

Re: Grinder Vac

Keith Tompkins

HI John, Good idea...it cannot be a good idea to breathe all the grinding dust, especially when grinding the high-cobalt content metals. I've seen guys true up their wheels using a heavy hand...the air is full of abrasive dust.

Re: Grinder Vac

#7

Re: Grinder Vac

John Jordan

One od those little can cyclones and you would never need to empty the vacuum, and no sparks would survive the cyclone.

Nice job.

John

Re: Grinder Vac

#8

Jesper, Denmark

Re: Grinder Vac

Jesper, Denmark



Here is my set-up. Very similar idea, but with minor differences. Steel can vacuum cleaner with standard filter as delivered. The energy in the sparks from the grinder is long dissipated before it reaches the vacuum cleaner.

There is no more ginding dust around. The vaccum cleaner and the grinder are both wired to the same switch on the wall, so when you turn it on, both run at the same time. The switch was added after the pic.

The vac is a bit noisy, but not so much that I have bothered to add a sound enclosure - yet!

Re: Grinder Vac

#9

Re: Grinder Vac

John Lucas

John I thought about the cyclone idea but I think the dust and particles are light enough that they would be pulled right through. I really believe that the sparks will be out long before they reach the vac. When I'm seriously grinding metal using a very course wheel or angle grinder it's rare for a sparks to fly more than a few feet and these are chunks far larger than I'll ever get from an 80 grit wheel.

I'm going to monitor it very closely for a while. If there are any scorch marks on the foam then I'll know I have a potential problem and will take care of it.

Re: Grinder Vac

#10

Re: That would be my concern.

John Lucas

Don It's not a closed cavity. It's a shop vac and of course has an outlet side as well as an inlet.

I'm concerned about fire but in reality I don't see how it can happen. You could throw sparks from an angle grinder directly at the plastic container of the shop vac and not light it on fire. It would take some effort with a match to even burn a spot on it. The only concern is the foam filter. Even then the filter is in an enclosed area and if any fire were to start it would burn up the oxygen pretty fast and put itself out. I'm still going to watch it very closely for a month or so and look for scorch marks on the filter.

Re: Grinder Vac

#11

Re: That would be my concern.

Mark Wollschlager

You might want to use a CleanStream or similar HEPA filter as the foam will allow most anything back out into the air until it is loaded.

The cost is moderate and they come with a deflector to redirect the incoming particles away from the filter to prolong its life.

mark

Re: Grinder Vac

#12

Re: spark arrester idea

matt overton

An idea to arrest the sparks is to redirect the inside intake downward toward the bottom of the vac and keep an inch or two of water in the bottom. Any fragments that are still burning have enough mass that they will fall to the water before getting to the filter. It will be a little messier when you clean the vac, but added insurance. I rigged a similar setup as a pre filter for my upstairs clothes drier to catch much of the lint before the horizontal run to the exterior vent and works well.

Re: Grinder Vac

#13

Steven Antonucci

Another potential issue if you grind aluminum

steven antonucci

If you make the mistake of grinding aluminum and steel together, you can run the risk of creating thermite (iron oxide and aluminum oxide). A spark could ignite it, and it burns at about 5000 degrees. You cannot put it out.

I have my grinder on a metal topped bench, and I sweep it from time to time. Not the cleanest are by a long shot, but I try to keep up with it.

Steve

Re: Grinder Vac

#14

Re: Another potential issue if you grind aluminum

Guy Bratt

Here's another thought to those concerned about sparks. There are vacumns made for cleaning wood burning fire places.

Re: Grinder Vac

#15

Re: Another potential issue if you grind aluminum

John Lucas

Steve Can't imagine using my good grinder for aluminum. That's why I have another grinder but in reality I usually use my 2" sander for grinding aluminum