Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Broken Vacuum Guage?

Posts

Broken Vacuum Guage?

#1

Broken Vacuum Guage?

HeatherAinAK

Hi, I have spent most of the afternoon trying to get my new Oneway vacuum check working. I hooked it all up in the kitchen and the pump (craft supply Gast pump) seems to work but I did not get a pressure reading on the gauge even with it hooked up just with the hose and a "T" with the ends occluded. I thought I would try the whole setup anyway and it again seems to work and has enough suction to hold the aluminum plate that comes with the drum chuck on so tightly that I can't pull it off. Again, no vacuum reading on the gauge. Is there something I am missing? It is a new gauge that came with the oneway setup. Is there a way to troubleshoot just the gauge? It is a fluid filled gauge and I have tried popping off the rubber stopper on the top to equalize the pressure bus still no luck. Bummer when you can't get a christmas present working!

Thanks,

Heather

Re: Broken Vacuum Guage?

#2

Re: Broken Vacuum Guage?

walta

Please post a photo of your setup, it’s worth a thousand words. But it is entirely possible the gage is defective.

Walta

Re: Broken Vacuum Guage?

#3

Re: Broken Vacuum Guage?

John Lucas

Check how you have it hooked up. It could be you've run the vacuum around it or have it on the wrong side. Of course it could also be a defective gauge. You coul hook the vacuum directly to the pump and plug the other side. With nothing else in the line the gauge would be the only thing to suspect.

Re: Broken Vacuum Guage?

#4

Re: Broken Vacuum Guage?

HeatherAinAK

Here are a couple of pictures. The pump tube goes to the bottom of the pipe under the gauge. Then the hose goes from the left of the gauge T to the vacuum adapter.

Last picture showing obvious suction.

Thanks,

Heather

Re: Broken Vacuum Guage?

#5

Re: Broken Vacuum Guage?

Doc Green

Sometimes the gauges are shipped with a small plastic stopper inserted in the port to keep various debris out. Be sure you have removed any such stopper that may be there.

You can test it by simply sucking on it. I can suck 6" Hg (one-fifth scale).

Good Luck, ~Doc

Re: Broken Vacuum Guage?

#6

This could turn into a contest!


Re: Broken Vacuum Guage?

#7

Re: Broken Vacuum Guage?

Tony Wheeler

what I see in your pic it looks like the exhaust port of the pump is blocked off mine has a hose to a filter on it

Re: Broken Vacuum Guage?

#8

Re: Broken Vacuum Guage?

HeatherAinAK

That is a little muffler that came with the pump. I tried it without it with no difference.

Heather

Re: Broken Vacuum Guage?

#9

Re: Broken Vacuum Guage?

Bill Turpin in WNC mountains

How about a close-up pic of guage face?

Re: Broken Vacuum Guage?

#10

Bill- do you want a photo of the gauge....

JamieDonaldson

...or Doc's face while he's sucking on it?? :D :D :D

Re: Broken Vacuum Guage?

#11

Re: Broken Vacuum Guage?

Don Evans

Heather:

I have a large monitor so I was able to go over your setup easily with the pictures you posted. Your setup is appears perfect!

So we know it is pulling pressure due to the plate not falling off the drum, so only thing in question is how much pressure is there.

So:

1. Is it very difficult to pull the plate off the drum or impossible or next to impossible? I have to jerk darn hard to get mine off when it is pulling 27hg.

If answer to either one of these is yes, then we can pretty much conclude right there it is a bad gauge.

2. Did you use teflon tape on all the joints or dope from a can (usually these have a brush attached inside to the lid? One problem with dope is it can be pulled into places it should not be, like the pump in this case, although possible, maybe, I don't see it causing the gauge to stop working. I've never had any luck with dope on air pressure or vacuum systems, so having done that once, it's teflon tape for me for everything now.

You asked how to check the gauge. Take the hose off the bottom of the pipe that is holding the gauge and connect it directly to the gauge. If you have hose left over I would just cut a 6" piece off and connect gauge with that short pipe directly to the pump. Look in the connector end of the gauge first to make sure you don't see any obvious obstructions. The rubber stopper you mentioned concerns me slightly, I've never seen one on this type gauge but that doesn't really mean anything. When you take the stopper out can you see a screw in the hole, perhaps it is a "Zero adjustment" screw so you can callibrate it to zero with no pressure on it, I don't really know.

FYI the liquid filled gauges are used to stop vibrations from machinery from damaging the gauges and also makes reading them more accurate. Nothing worse it is area that trying to read a gauge that is bouncing from 20 to 28hg, hopefully an obvious joking here, hope you Powermatic never sees that much jumping up and down.

Don

Re: Broken Vacuum Guage?

#12

Re: Bill- do you want a photo of the gauge....

Bill Turpin in WNC mountains

The pic of guage doesn't look quite kosher to me. I want to make sure that it is really a vacuum guage.

Re: Broken Vacuum Guage?

#13

Re: Broken Vacuum Guage?

Bill Noce in Northeast Ohio

After looking at your guage at 200% Magnification(sp) and comparing it to mine. My needle is on the left side of the gauge an when vacuum is put to it the needle moves up to the right(CW), your guage the needle looks like it is already all the way on the right side am I right. So it could be broke.

Re: Broken Vacuum Guage?

#14

Re: Broken Vacuum Guage?

del schisler

here is a vaccum gage what it should look like http://www.grainger.com/Grainger/Vacuum-Gauge-4FLP6?cm_mmc=GooglePLA-_-Test%20Instruments-_-Pressure%20and%20Vacuum%20Measuring-_-4FLP6&ci_src=17588969&ci_sku=4FLP6&gclid=CPK215bApa0CFcfe4AodOF68OQ

Re: Broken Vacuum Guage?

#15

Re: Broken Vacuum Guage?

HeatherAinAK

Here is a close-up. It looks just like the oneway catalog pic. I pulled off the stopper and I think it is just a fill hole for the liquid. All you see inside are the gauge guts. I found another gauge in the garage (from an old military suction pump) but it has a smaller fitting. I am going to go get a reducer. Thanks for all the help all, will keep you posted.

Heather


Re: Broken Vacuum Guage?

#16

Jim Evans

Re: Broken Vacuum Guage?

Jim Evans

No wonder it won't work, it's a left handed gauge. 8)

Re: Broken Vacuum Guage?

#17

Re: Broken Vacuum Guage?

HeatherAinAK

OK, good news or bad news depending on how you look at it. Bad news, broken gauge. Good news, everything else works! I got 22 mmHg vacuum on initial reading.

The Gast pump manual says do not use teflon tape but I don't like the idea of sucking in pipe dope. What are your preferences?

Thanks again for the help.

Heather (still trying to get the visual of Doc out of my mind!)

Re: Broken Vacuum Guage?

#18

Just to be sure . . .

Doc Green

Heather, the stopper I was thinking might be there will be located inside the threaded part where the gauge attaches to its female counterpart. If there is no stopper, you should see a small hole, about 1/16" or even smaller.

The reason for not using teflon tape is that sometimes it shreds and can possibly introduce "stringers" into the system. You can avoid this just by not letting the tape lap down over the end of the fitting when you wrap it. I use it all the time.

And, ha ha ha, . . . the visual you have of me testing the gauge is not nearly as bad as the real thing would be. :)

~Doc

Re: Broken Vacuum Guage?

#19

Re: Just to be sure . . .

Bill Turpin in WNC mountains

After 42 years of industrial maintenance experience I have had bad times with both tape and dope. Leave the first two threads CLEAN of either. The National gas code will not allow teflon tape on fuel lines because it shreads and can keep valves from closing in an emergency. I prefer quality dope with teflon in it.

Another thing about vacuum systems. Double the length of sucking yields one fourth the volume of suction. Reduce the diameter of the smallest port by half yields one fourth the volume sucked. A 3/8" orifice is 2.249 times larger than a 1/4" orifice.

Re: Broken Vacuum Guage?

#20

Re: Just to be sure . . .

Don Evans

Bill assuming you are correct on the sizes and quantities you state wouldn't a small fitting in the system anywhere just reduce the TIME it would take to reach maximum vacuum? It would not reduce the max vacuum capabilities?

Don

Re: Broken Vacuum Guage?

#21

Re: Just to be sure . . .

Bill Turpin in WNC mountains

I was referring to the volume of the air evacuated. The net effectiveness of the pull is a factor of this volume vs the combination of leaks from plumbing, leaks thru pores of wood, volume of object being sucked on, etc. If the leaks are more than than volume pulled the system will not hold your object. Time can not overcome too much insufficient volume. Bottom line in English: a single 1/4" fitting in a 3/8 system will cut your vacuum ability by three quarters. Time and max vacuum all fit together. Make the hose to pump as short as practical. The vacuum (volume) pulled is inversely proportional to the square of the diameter or length. I hope this makes sense. If your pump has a small port, then it makes no sense to run larger lines.

Re: Broken Vacuum Guage?

#22

Re: Just to be sure . . .

Don Evans

I see what you are saying, thanks

Don

Re: Broken Vacuum Guage?

#23

Re: Just to be sure . . .

Bill Turpin in WNC mountains

A sneaky problem with all this. Inspect the inside diameter of all fittings. Many times 3/8" fittings can have interenals of 1/4". If this happens change brands, suppliers, etc. Sometimes, just look at a different fitting in the bin. Street ells usually are much more restricted than an ell and a pipe nipple. Make your system to have the maximum vacuum. If too much, have an inlet valve that you can open to bleed off the excessive vac. Better to have too much than not enough. You can also bore out undersized fittings to make them more efficient.