Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

BAD INFLUENCE

Posts

BAD INFLUENCE

#1

BAD INFLUENCE

Lewis Dodd

Well, you guys are a BAD INFLUENCE!

I have toyed with the idea of getting into wood carving and piercing ever since Gary Roberts and I crossed paths at a SWAT convention. I read the posts on piercing below and suddenly felt the BITE.

Alas, it means buying more TOOLS! Need some guidance here, approx. how much am I gonna spend to see if I like it, some good "how to" books, rec. tools, such as foredom vs ???., and WHY DIDN'T THINK OF THIS TO PUT ON MY CHRISTMAS LIST THIS YEAR?

Let me put it this way, piercing is making holes in your turnings, am I right so far?

Re: BAD INFLUENCE

#2

Re: BAD INFLUENCE

Dick Wilson

Lewis, CONGRATULATIONS!!! You are now in the vortex. Trying to excape is futile. :D Without spending hundreds of dollars you could use a Dremel, flexible shaft, and Rotozip tile cutting bits. It sure won't be intricate piercings like many but you will learn whether it is something you want to pursue. Good luck.

Re: BAD INFLUENCE

#3

Re: BAD INFLUENCE

Donna Banfield

I'm not a guy, but I can offer some help in spending your money :-)

If you want to pierce, you'll need a tool that can run at 350,000 to 400,00 rpm. Anything less, and the bit will want to follow the wood grain, making it hard to control the direction in which you want to do your cutting/piercing. I don't know if Foredom tools run that fast, as I've never used, nor looked into them.

The best tool for piercing right now is the NSK Presto, used and sold by Binh Pho and J. Paul Fennell, as well as other specialty wood carving stores.The Presto is oiless, the Powercrafter, another high speed carver, needs oil. There have been a few threads on other forums about the Powercrafter, and the downside of this tool.

High speed carvers need air to run them, so if you don't have a compressor, you'll need one. You'll also want a second regulator set up right where you're doing your carving/piercing. These tools are not cheap, (handpiece that holds the bit is about $360.00) and running them with too much psi can ruin a handpiece and the micromotor that's inside. You'll want to set your secondary regulator at around 38-40 psi.

Remember that these tools are not just for piercing; they can be used for texturing and carving with extreme detail....if that's something in which you're interested.

Hope this helps spend your money :-)

Re: BAD INFLUENCE

#4

Re: BAD INFLUENCE

Lewis Dodd

Well, didn't mean to possibly slight you Donna, but look at it this way you are exempted from being a bad influence!

Thanks for the advice, I know my question is awful general, kinda like asking "how fast do I turn" sort of thing. It is a whole new facet to me and I kinda wondered how to "test it out". It took me 4 upgradings to finally get to the Oneway, believe it or not I started with a 1/2 hp Sears, even had a Grizzly thrown in there somewhere.

Thanks for the help, gonna start searching for some books on the subject, you know, layout, procedure, etc.

Re: BAD INFLUENCE

#5

Re: BAD INFLUENCE

Don Evans

Lewis:

As far as the word "Foredom" goes, forget u ever heard it. You can get a more powerful unit and for less money called a "Mastercarver". 1/3 hp and I understand they have come out with one that is 1/2 hp but the 1/3 is more than enough. Most Foredoms are 1/6 or 1/8 hp. Check it out. It is ruggedly built and you can get the initial setup with 3 handpieces, reciprocator, detail handpiece which uses collets 1/16, 3/32 and 1/8 plus another handpiece that has a drill type chuck which will take from 0 to 1/4" shaft burs. All that for less than the one we are not going to mention anymore.

It also comes with flexshaft that is much more flexible than the dremel shafts if you are familiar with them, it's really the same exact shaft that foredom uses.

I also highly recommend you get the bench mount with it instead of a foot operated pedal. The bench mount gives you variable speed and the unit still has a built in wire to hang it if something requires it.

Every bur and sanding mandrel has a speed that it works best at so there really isn't a need for foot control to constantly vary it. With the bench mount you can set the speed and just concentrate on your work. The unit is also reversible.

You can also use other peoples handpieces with it but Mastercarver has every kind you'll probably ever have a need for.

Google Mastercarver and you'll get lot of information on it. Understand that this unit is for reciprocating, sanding and bur carving. As Donna said you cannot get the delicate piercing that you have seen on woodturnings unless you go to the much high speed units like the NSK or a regular 90 deg dentist drill. These units work off an air turbine, nothing really but two bearings a shaft and a turbine that looks like a little gear with the teeth on it.

I have no affiliation with Mastercarver, but happy owner and user for several years.

I also have air turbine units for the piecing stuff.

Don

Re: BAD INFLUENCE

#6

Re: good INFLUENCE

bill Crommett

Many years ago Frank Sudol gave a demo at our club about deep tuning and piercing. I was influenced to start deep turning and piercing, until I turned my first deep bowl/vase at 22 inches deep and that turned me off and that form sits on the kitchen cabinet as my only copy of my "never again " series.

Re: BAD INFLUENCE

#7

Bill Blasic

Re: BAD INFLUENCE

Bill Blasic

I also have the Mastercarver and agree with what Don said.

Bill

Re: BAD INFLUENCE

#8

Re: BAD INFLUENCE

Hal Taylor

In addition to the Mastercarver, you'll need to spend a bit more money too on a Mastercarver Micropro which is a micro motor hand piece. This has become invaluable to me in addition to the larger unit and the dental drill I use. Welcome to piercing...

Re: BAD INFLUENCE

#9

Lyle Jamieson

Re: BAD INFLUENCE

Lyle Jamieson

I have to agree with Donna here. The Foredom, Mastercraft, Dremmel, type carvers and great for carving, I use them all the time on my torso sculptures. But they are not the right tool for piercing. I suggest you ask around in your club and use the high speed dental type tool before you buy it. The turning must be really thin and uniform and it is detailed, tedious work (read Boring) and is not for everyone. I dont have the patience to sit for hours doing that much detail. When you need to work for hours on a piece it is necessary to have the lightest tool possible or your hand goes numb.

Re: BAD INFLUENCE

#10

Re: BAD INFLUENCE

Lewis Dodd

Thanks Lyle I will ask, but to date I know of no one in Hill Country Turners that does piercing, perhaps Andy Chen, but haven't crossed his path in a long time. Who knows, perhaps one has tried and disliked it and wants to recover a little Christmas money. From what I have Gleaned so far, I have pretty much settled on the NSK , bout $50.00 more than the Mastercarver from Brad Packard. Still, gonna have to save some $ to just "test the waters " at this point but I want to give the art a fair chance by using adequate tools to start the learning curve and "taste" the procedures.

Re: BAD INFLUENCE

#11

Re: BAD INFLUENCE

Don Evans

Hal:

I have not seen a need, for me yet, for one of the micro motors. I've always managed to get by with my dremels, mastercarver with 3 different heads and my powercrafter and 2 dentist 90 degs.

Seems to me the micro motor would fit between the mastercarver and the high speed turbines.

So, what will the micro add? I do see more flexibility with it (no flexshaft holding back a particular angle attack). They are a big jump money wise so is it really that valuable and in what way?

If one's pockets are very deep not a problem I guess, but retired now and consider myself well off but still cannot afford that Bugatti Ceylon with 1000 hp.

Don

Re: BAD INFLUENCE

#12

Re: BAD INFLUENCE

Hal Taylor

Don, in addition to piercing I "carve" as well. The handheld microcarvers are much lighter, easier to use and hold, and run a lot faster than the Foredom/Mastercarvers. The brushless micro motors are very pricey, but the ones with brushes (Microcarver Pro) are not that bad cost wise for what they will do. They do fill a niche between high-speed piercers and Foredoms.