Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Chatter Work - An easier(?) method *LINK*

Posts

Chatter Work - An easier(?) method *LINK*

#1

Chatter Work - An easier(?) method *LINK*

Craig Daymon

I was flipping through an old Craft Supplies catalog and saw the Henry Taylor Elf Decorating/Texturing tool. I read the description and thought it would be pretty easy to make one myself. (I have several carving burrs and plenty of rare earth magnets in assorted sizes already.) Doing a quick search on-line for more info, I found out I'm not the first to make my own. Anyone using this tool or already made their own?

Henry Taylor has 4 great videos on using the tool on their site (link below) and Highland Woodworking has the plans for making your own, as well as a $29.99 kit of the needed parts.

http://www.highlandwoodworking.com/mini-texturing-tool-kit.aspx

Rather than buying bearings and a router collet (or the kit), I'm going to make my own bearing from UHMW plastic, which I already have. I'll turn the UHMW to fit my tubing (copper, Lowes didn't have any brass tubing) and drill the appropriate size hole for the shank of my carving cutters. Ideally, I'll drill the hole so the shank extends by about a quarter inch and then part off my "bearing" with about 1/32" between the end of the "bearing" and the bottom of the hole. That way in use the shank won't be in direct contact with the magnets.

-Craig

P.S. Even if you create chatter work using a traditional chatter tool, the videos are worth checking out. The 3rd one shows some very interesting patterns using multiple cutters.


Elf Decorating Tool Description and Videos

Re: Chatter Work - An easier(?) method *LINK*

#2

P.P.S.  Yes, I know this isn't "chatter" work

Craig Daymon

But the results are very similar and, based on most of the chatter wor I've seen, are cleaner.

Also forgot to mention that I picked up a natural bristle brush to use as a burnisher with the tool, after I trim the bristles short.

Re: Chatter Work - An easier(?) method *LINK*

#3

Re: P.P.S.  Yes, I know this isn't "chatter" work

John Lucas

Craig I like the idea of the UHMC. I think I have some, I'll have to try it. I had plans to build an ELF but then fall semester hit and ate up all my free time. I may work on it this week end if I don't forget. Thanks for posting.

Re: Chatter Work - An easier(?) method *LINK*

#4

Re: Chatter Work - An easier(?) method

robo hippy

I don't know why you couldn't just chuck it in your dremmel, and let it free spin.

robo hippy

Re: Chatter Work - An easier(?) method *LINK*

#5

Elf substitute

Jim H

I haven't had the opportunity to try it out but have heard of people using Dremels or Fordom hand pieces with out power, just letting them free wheel. If it works, it would be a whole lot simpler. Although making tools is half the fun.

Re: Chatter Work - An easier(?) method *LINK*

#6

Re: Chatter Work - An easier(?) method

Jim H

I guess I'm a slow typist, swear your reply wasn't there when I started :-)

Re: Chatter Work - An easier(?) method *LINK*

#7

My elf experiments

mjonesrdg


I removed the handpiece from my flex shaft to allow complete free wheeling. One of the constucts is made from an old brass drift and a pretty white mohagany handle that I made for it. The multi piece assembly utilized a magnet to retain the burr, and the bottom of the shaft runs directly upon it. The brass pretty one uses a drop of oil in the brass tube bushing to keep the burr form falling out (suction)

The piece of ash with my "play time" show some variety of decoration that you can obtain right out of the box. Not much of a learning curve before you are ready to put it to real use.

Except for the "play time" and learning, the tool is not likely to be in use for more than a few brief moments at a time. I found that all three of these worked equally well, and found no serious setbacks with the use of any.

Hope this helps...

Mike in redding Ca.

Re: Chatter Work - An easier(?) method *LINK*

#8

Re: Elf substitute

Stuart Johnson

I tried making one using a disabled disc grinder. It didn't work well and wore a small nick in my Robust tool rest when I let the shaft of the burr lay on it. In my case at least this is a time it is better off to buy the product.

Re: Chatter Work - An easier(?) method *LINK*

#9

Re: My elf experiments

Craig Daymon

Very impressed with your results, especially the quality of the cuts in Ash, which is not the easiest of materials for this type of work.

I like the convenience of just using my flex shaft carvers handpiece, though I'll still likely make a separate tool just for the fun of working through the design. I'm anxious to see how the UHMW plastic works for a bearing.

Not to drift too quickly, but I'm wondering how the magnet retention idea (and UHMW plastic) would work to create a free spinning inertial sander as well. If making one at a fixed angle, could do some multi-axis spindle turning to set the angle.

-Craig

Re: Chatter Work - An easier(?) method *LINK*

#10

i have an elf..it  makesnteresting patterns..


Re: Chatter Work - An easier(?) method *LINK*

#11

Re: i have an elf..it  makesnteresting patterns..

Jim H

My shop elf keeps hiding my tools. :b

Re: Chatter Work - An easier(?) method *LINK*

#12

Jim Evans

Re: i have an elf..it  makesnteresting patterns..

Jim Evans

Kids say the darnedest things. From my granddaughter via my great grandsons.

I forgot to move our Elf last night... Jackson came in here freaking out and said "I think Jordan touched him and he lost his magic because he is still in the same spot!!" haha :)

Re: Chatter Work - An easier(?) method *LINK*

#13

Steven Antonucci

Kids saw me move the elf...

steven antonucci

it was a Christmas tragedy!

(I didn't know that I could break his magic. Thinking on my feet, I told the boys that I had accidentally transfered my "mad skills" to him and he would be making bowls in the shop while I slept)

Joey was not amused, but now thinks it's funny because I hung a shaving off of the elf to prove it...

Steve