Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Threads again. Strengthening with acrylic.

Posts

Threads again. Strengthening with acrylic.

#1

Threads again.  Strengthening with acrylic.

Craig Daymon

Cutting thread in end grain is always going to create weaker threads than those in face grain (of the same kind of wood) since you are cutting the grain into stacks of tiny pieces. Threads in softer woods are frequently problematic.

So how to strengthen them. Many use cyanoacrylate, but that is brittle and is reported to not last over the years. (For any gluing purpose.)

A local turner has stabilized pen blanks by throwing them in a vacuum container in a bath of acrylic shavings dissolved in acetone and keeping them under a vacuum for...a couple days.

I don't have the equipment or desire to stabilize a blank large enough to turn a box, but I'm wondering if painting the area to be chased with the same acrylic and acetone solution would be an ideal way to strengthen threads. It's easy enough to make and can be brushed on with a disposable glue brush.

Thoughts? Comments?

Thanks,

Craig

P.S. Also I'm wondering how this solution might work as a very impenetrable finish. I think it is a bit gummy, so after cured you'd probably have to sand it smooth and polish it the same way you would finish a solid acrylic turning, but it might protect those wood colors that are affected by exposure to air.

Re: Threads again. Strengthening with acrylic.

#2

Steven Antonucci

That is a decidedly "Try it" project

steven antonucci

Idea had merit, but the result is probably so specific to the wood, your skill, and the moon being in Aries that you are going to have to give it a shot to let us know what happens.

I have not had much luck with the acrylic kit I bought at Michael's. YMMV

Steve

Re: Threads again. Strengthening with acrylic.

#3

Another trick used by boat builders,

Keith Newton

is to drill an oversize hole, then fill with thickened epoxy, then drill and tap it. Of course, when there is a balsa core between fiberglass, I usually fit a specially ground old allan wrench into a drill chuck, which will cut the core back larger than the hole through the glass skin, which really locks it into the hull once filled.

You could get the same effect by drilling larger, and maybe using a T slot router bit like made for hanging pictures.

And of course there are a lot of press-in nylon bungs made for the 32 mm system, already threaded.

Re: Threads again. Strengthening with acrylic.

#4

Re: Another trick used by boat builders,

Don Evans

Just a clarification on the router bits you mentioned:

The bit used to hang pictures is called a "keyhole" bit, the "T" slot bit is different bit and only makes the wider cut at the bottom of a slot which has been cut with a straight bit.

Physically the big difference is the keyhole bits shaft also cuts and the larger end of it drills a hole when plunged into the wood also.

None of this really matters to this thread but though some may want and or need to know difference.

Don

Re: Threads again. Strengthening with acrylic.

#5

Thanks Don. Brain freeze, or old age.


Re: Threads again. Strengthening with acrylic.

#6

Re: Threads again.  Strengthening with acrylic.

Doug Turner

A trick I picked up from Mike Mahoney when he is turning threaded tops for urns is to turn the hole oversize and then glue in a boxwood washer. The washer can be turned true and threads cut into the boxwood. The washers were about 3/16" thick with similar sized walls. If the finial won't accept thread a suitably sized boxwood plug with a doweled turned on top can be glued into the finial wood.

Re: Threads again. Strengthening with acrylic.

#7

Re: Threads again.  Strengthening with acrylic.

John Lucas

Craig In my experience solid wood doesn't soak up the acrylic or CA glue etc, unless it's porous or punky. When I've tried soaking good sound wood like cherry with different products to strengthen the threads it doesn't work. That's why I bought the Baxter threader because I just couldn't chase threads in softer woods.

What I do is kind of mentioned above. I replace the wood with something better. You can do what was mentioned of course and that is to glue in wood that threads well.

Mostly what I do now is simply cut a groove, fill it in with epoxy, turn away the wood and chase threads into the epoxy. You can color the epoxy if you want. If you leave it clear and have some wood backing it up it picks up the color of the wood and looks pretty nice.

I'll be doing that tomorrow if I get time so I'll post a couple of photos to show the process.

Re: Threads again. Strengthening with acrylic.

#8

epoxy threads

John Lucas

I needed to thread some yellow heart and last time I tried it didn't thread very well by hand chasing. I filled a groove with epoxy and then turned away the wood on the outside and chased threads in the epoxy. It worked perfectly. Then I decided to try and chase threads in some of the waste and it worked pretty well. I did coat the area with Johnsons paste wax, both before and during the chasing.