Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Spindle Roughing Gouge

Posts

Spindle Roughing Gouge

#1

Jim Evans

Spindle Roughing Gouge

Jim Evans

Has anyone used a SRG upside down as a scraper?

I was watching a video from Wood Magazine and the guy turned his large SRG upside down and used it as a scraper. It just didn't look like a good thing to do to me.

Re: Spindle Roughing Gouge

#2

Re: Spindle Roughing Gouge

Lan Brady

Jim,

The SRG is shapened upside down and radiused. It works great on segmented work. It saves a lot of sanding.

Lan

Re: Spindle Roughing Gouge

#3

Re: Spindle Roughing Gouge

George Van Beynen

Firmers gouges have been used by many for this same purpose. I always hear or them as a Hill scraper but Joaz told me he was not the originator of the idea. They are sharpened with the flute facing down on the rest and work as a curved scraper. Work great on the inside, concave surfaces of a bowl. The curve seems to provide a sheer scraped surface.

Re: Spindle Roughing Gouge

#4

Got a picture???

adrien

Sharpened on the inside?

So it can no longer be used as a roughing gouge??????

Radiused? No longer with a straight front edge?????

Re: Spindle Roughing Gouge

#5

Ken Vaughan

Found an old link and Picture

Ken Vaughan

http://www.woodcentral.com/woodworking/forum/archives_turning.pl/bid/2108/md/read/id/193428/sbj/found-the-shear-scraper-photo/

The links to Joaz Hill site do not produce the expected outcome. Found an article in the Savanna Woodturners tips - but the pictures appear to be dead.

Re: Spindle Roughing Gouge

#6

Thank you. Just as I feared.


Re: Spindle Roughing Gouge

#7

Jim Evans

Re: Got a picture???

Jim Evans

Sharpened as a gouge. He had just used the gouge to turn and then turned it over and used it as a scraper.

I'll see if I can get a capture.

Re: Spindle Roughing Gouge

#8

Re: Got a picture???

George Van Beynen

It is not usable as a gouge once sharpened as a scraper. The photos were from Joaz Hill.





Re: Spindle Roughing Gouge

#9

Ken Vaughan

Thanks for the Pictures, George

Ken Vaughan

I note that the original discussion appears to be concerning spindle turning (face grain) and the Joaz Photos are with bowls (mixed face and end grain)

Certainly hope no one was advocating using a tanged spindle roughing gouge on bowls other than turned over and as a scraper.

(I see some value to some old high carbon steel shallow gouges in the old tool bucket -- Thanks again for the photos)

Re: Spindle Roughing Gouge

#10

Re: Spindle Roughing Gouge *LINK*

Craig Daymon

I've used my German Spindle Gouge, a type of roughing gouge similar to the one used by Rude Olsolnik, inverted as a scraper. It works very well. I've used it inside of bowls. I bought mine from Packard Woodworks and it is one of their tools. If you have their catalog, there is a picture of it in there. Mine is either the 1" or 1.25" tool, I forget which.

If you go to the Woodturning Tools page on their site, I think the tool in the middle of the 5 shown there is the German Spindle Gouge. The specific page gives a very good close up of the flute and grind.

-Craig


German Spindle Gouge page at Packard