Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Drying experiment.

Posts

Drying experiment.

#1

jim miles

Drying experiment.

jim miles

Over the years I have tried about all the methods for drying rough turned pieces and for the most part have settled on the " rough turn it and set it aside and wait to see what happens" method. However of recent I have been experimenting with a method I have not seen elsewhere. Using metal band clamps. I rough out the piece. Sometimes you have to intentionaly turn a place to put the band. Then tighten the clamps as the piece dries. It seems to work pretty well. I am getting less cracking on hollow forms. I also use it on bowls, but it dosen't seem to work quite as well there. You can see in the pic at the bottom where there is not a clamp that it is cracking, but not the rest of it. Also I have been able to get some cracks already in the wood to close up with the band clamps. Anybody else tried doing this ?

Re: Drying experiment.

#2

jim miles

Re: Drying experiment.-with Pic

jim miles


Re: Drying experiment.

#3

Brad Vietje

Re: Drying experiment.-with Pic

Brad Vietje

Hey Jim,

I can't tell the orientation very well from the photo posted... are you turning on the pith (turning away the bark and sapwood all the way 'round) ?

I turn a lot of hollow forms from green wood (sometimes to completion in green wood, and more often part turn, dry, and then finish turn), and I only rarely lose a piece to cracking. I find the most important factor is the thickness of the hollow form walls needs to be pretty close to the thickness in the foot or mounting area.

It looks like you have much more mass in the base for chucking, which would make cracks in the base far more likely.

I usually turn a small "foot" shaped for my chuck jaws, and often the base of the final piece projects right down between the jaws. The tenon I grab might be only a 1/4" ring surrounding the base of the piece. I turn this all away when finishing the piece between centers after re-turning and sanding.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Drying experiment.

#4

Steven Antonucci

interesting

steven antonucci

I thought about doing that on a bigger bowl with a band clamp. Do you get any staining on the wood?

Steve

Re: Drying experiment.

#5

Re: Drying experiment.

John Lucas

I tried it once. When I turned my Cardiac lamp I turned it out of a whole log with the Pith in the center. I needed it to stay as round as possible so I centered the pith and then hollowed it completely through. I was hoping that any wood movement would be equal all the way around.

I didn't trust just that however so I put band clamps around both ends. Not to keep it from cracking, it was about 1/4" thick, but to try and keep it round because I had planned to put aluminum circles around part of it. It either worked or the wood worked for me because is was out of round only about .o2o" or so. I was able to trim it to fit the aluminum rings so no one but me knows.

Re: Drying experiment.

#6

jim miles

Re: interesting

jim miles

Band clamps are stainless steel ( I think ) never had any stain

Re: Drying experiment.

#7

Re: Now we all know...


Re: Drying experiment.

#8

Re: Drying experiment.-with Pic

Darryl

I used band clamps to take out the oval of a small bowl I turned to try Bin Pho's piercing. It was green when I hollowed it. When it dried it was warped badly. After re wetting it and applying the clamp it returned to being circular and I was able to pierce it.

Re: Drying experiment.

#9

Re: Drying experiment.

robo hippy

I have figured that my wrapping the rims of my bowls with the stretch plastic film does the same thing: compression on the outside helps keep the bowl from splitting. The rim is the weak spot where cracks are more likely to start. While the compression from the plastic film won't be as much as from your band clamps, I figure the plastic helps keep the moisture in. Rounding over the edges of the rim are almost as important. The sharp edge is more prone to cracking, perhaps because it doesn't keep to the 'even wall thickness' idea, and rounding them over does help that a bit.

robo hippy

Re: Drying experiment.

#10

Another re-hydration success story!


Re: Drying experiment.

#11

Re: Another re-hydration success story!

John Jordan

Bob Stocksdale was using clamps 30 or more years ago. He turned a lot of exotics with the pith through them. Kept his roughed out bowls in the kitchen and would tighten the clamps daily. He seemed to believe it worked, I don't know. :D

It would serve to force a bowl shape to stay more round.

John