Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Lathe Stand Help!

Posts

Lathe Stand Help!

#1

Lathe Stand Help!

Ricc havens

I have an older Nova 3000 with the metal (not cast iron) open stand. The previous owner had made the lathe mobile by adding 2X6's across the bottom and adding castors to the legs. But the stand moves even when the casters are locked. I have used the 2X6 cross members as shelving for blank storage. The storage greatly reduces access behind the lathe for cleaning shavings.

I want to remove the castors but I am looking for ideas on how keep the shelving between the legs but yet be able to move the lathe to clean up wood shavings from behind.

Any ideas? Any pics of what you have done?

Thanks

Ricc Havens

Elkhart, IN

rv.havens AT gmail.com

Re: Lathe Stand Help!

#2

Steven Antonucci

If it is the sheet metal stand (Black)

steven antonucci

just drill a hole in it and add a block across the stand to put your shelf on?

S

Re: Lathe Stand Help!

#3

Lyle Jamieson

Re: Lathe Stand Help!

Lyle Jamieson

The important thing is to sturdy up the legs. I would bolt on a sheet of plywood on three sides leaving the front open. Run the plywood all the way from the top of the legs to a few inches off the ground. This will stiffen up the base and make the Nova almost purr like a robust. Leave just enough room to sweep under. Put bolts through the leg holes for leveling feet, (a must do). Now with the plywood frame it is easy to add a box under the lathe for sand. The mass is needed when you start putting natural edge or multi axis work on it to minimize vibration. Now you can still have room on top of the box for storage. Do not make the box all the way out to the front of the legs so you have knee and kick room to stand with your toes up under the bed

Re: Lathe Stand Help!

#4

Re: Lathe Stand Help! -  clarification

Ricc havens

I am looking for ideas and pics on how to once in awhile temporarily move a lathe. Somewhere I remember someone mentioning they used those wheeled crank trailer jacks. Would like to see that Idea in action. Or others where I can temporarily lift it on casters then move it then drop it back down to a firm footing.

Steve - it is the sheet metal legs. Yes I can add a shelf but also looking for ways to move it room time to time to better clean behind.

Lyle - thanks for the plywood suggestion.

Thanks

Ricc

Re: Lathe Stand Help!

#5

Steven Antonucci

How I clean behind my lathe.

steven antonucci

First, I have the cast iron legs. I built my box above the floor level, which means that I get wood until it, behind it, and anywhere near it. I have it far enough from the wall to push a broom all around it.

Secondly, I only do a cursory clean. I am not a neat freak. There is always sawdust around my lathe. I don't care unless it is a huge pile, which I remove with a shovel.

Lastly, on the rare times when I do a comprehensive cleaning (maybe once a year?), I open the garage door an blow it out with the leaf blower. I wear a mask and usually get down to pavement in 5 minutes. A shop vac is useless for the quantity that a lathe can produce and a dust collector clogs quickly unless you spend a lot of time pre-cleaning. A leafblower (electric) makes quick work of it, and I just blow it into the driveway before blowing the driveway clear.

steve

P.S. If you really have to move the lathe, I'd make one big moving dolly. Lifting is easier if you remove the extra bed, tailstock, banjo etc...

Re: Lathe Stand Help!

#6

Re: How I clean behind my lathe.

Bart Leetch

http://www.zambus.com/

http://www.greatlakescaster.com/products.php?cat=277