Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Finishing with lacquer

Posts

Finishing with lacquer

#1

Finishing with lacquer

Hal Taylor

Trying to get some info of experience others have in spraying lacquer. I have been using rattle cans with very good success, but it gets expensive. What about other spray methods? HVLP? Recommendations of lacquer for spraying? Etc.

Re: Finishing with lacquer

#2

Re: Finishing with lacquer

Skip Beardsley

I use lacquer which I purchase for our local Sherwin Williams dealer. I have a regular compressor set up with a good Binks gun. I run the pressure back to about 30psi which seems to work for me. I spray outside in the summer only as my shop is heated which a propane furnace with a pilot light which is on all the time so don't take a chance. In the winter I will use salad bowl finish for most of my bowls and leave the ones I want to shoot aside until spring.

Hope this helps.

Skip

Re: Finishing with lacquer

#3

Re: Finishing with lacquer

Darryl

there is a very inexpensive spray gun that I use. It is called "The Critter". Run about $40 or so. Uses a pint Mason jar. When finished spraying I keep one jar with acetone that I run through the gun to keep it clear. I generally run it about 40# and use lacquer from the local big box store. I like the Deft semi gloss finish myself. Usually about three coats is needed. I do use a mask when spraying and do it outside when the temp is above 50 degrees. The gun works well. You can not adjust the pattern of the spray like you can with more expensive guns. You can get them at several places I think Amazon has them. I also changed the filler spout to SS since the aluminum one breaks if you drop the gun. I believe the place where I found the SS tube also carries them but can not remember where that was Goggle it.

Re: Finishing with lacquer

#4

Re: Finishing with lacquer

John Lucas

I spray outdoors and use one of the cheap HF touch up guns. Ithink they run about $20. It doesn't always lay down really clean but it's close enough that Beal buff levels it our for me. Somedays I can really get the dillution right and it levels very well and others it leaves a sort of sandy looking surface which is easy to buff out. I thin the lacuqer less thann 50%, probably more like 30. I think most of my problems are just the wildly changing humidity here in Tennessee.

I leave the lacquer in the gun unless I'm not going to use it for a few weeks or more. I sometimes have to remove the tip and soak it in lacquer thinner for a few minutes but that's about it.

I do buy a professional grade lacquer from a local supplier called Benco. It is much harder than the Deft brush on lacquer I used to use so it buffs out easily.

Re: Finishing with lacquer

#5

Re: Finishing with lacquer

Grant Wilkinson

I use a pre-cat lacquer that I buy from a local supplier. I follow his recommendation to thin it by 10% for use with my Fuji HVLP. It is the easiest finish that I've ever worked with. It goes on nicely and dries quickly. I scuff with 320 grit between coats and I can re-coat in about half an hour.

Re: Finishing with lacquer

#6

Re: Finishing with lacquer

Hal Taylor

Darryl, I've noticed on the can directions to not spray Deft from the can as well as from some other cans. Can one disregard the caution?

Re: Finishing with lacquer

#7

Re: Finishing with lacquer

Hal Taylor

Grant, what brand do you use, and do you clean your sprayer after each use?

Re: Finishing with lacquer

#8

Re: Finishing with lacquer

Grant Wilkinson

Hal: I buy locally from Royal City Paints. I don't know who supplies him. Steve runs the place and teaches finishing at the local community college. He is really good about providing advice to newbies like me. I started using his pre-cat on the advice of a good friend who is a cabinet maker, and I haven't used anything since.

I clean up with lacquer thinners.

Re: Finishing with lacquer

#9

Re: Finishing with lacquer

Dick Coers

Almost any gun will give you a better finish than a rattle can. Rattle can nozzles and lack of pressure control will almost always give you a lot more orange peel than from a gun. Sherwin-Williams is a good place for advice. You can get some pretty cheap HVLP guns now, but with the small amounts of finish we use at each use, and needing a fairly small fan pattern to spray turnings, a conventional gun really isn't a bad choice. Stop by any local woodworking/cabinet shop for advice where they buy their materials.

Re: Finishing with lacquer

#10

Re: Finishing with lacquer

Darryl

Hal your question is a good one. The limitation on spraying is one placed on us by EPA because of the VOQ fumes. Deft is specified as a brush on lacquer because of the regulation. You can spray it but in doing so you do run counter to EPA regulations. The product does spray well regardless of the brand. One thing that is good about lacquer is that when you apply subsequent layers it "melts" into the the previous layer giving a smoother finish.