Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Chuck

Posts

Chuck

#1

Chuck

Don at Central Illinois

I have a Technatool chuck and one of the 'allen' screws has worn away and I can't tighten it. Other side works great. Who is the representative for Technatool these days? Just want to get some parts and try to repair it. Thanks in advance.

Re: Chuck

#2

Teknatool Support

Jeff Willaford

Teknatool Service Center (based on last info they sent to me)

Our office is open from 8am to 6pm, Monday to Saturday. An afterhours urgent message service is available outside of these hours.

Our toll free number remains the same:

1-866-748-3025

Our contact details

Teknatool NOVA

4627 Chancellor St, NE

St Petersburg

Florida 33703

Toll Free Calls - 1-866-748-3025

Toll Free Fax - 1-866-748-4193

Phone - 727-346-4775

Email - service@teknatool.com

Re: Chuck

#3

Re: Teknatool Support

Darrin Hill

good luck with that...

took me 3-4 weeks to get them to get them to send me something..

first time i left messages, then emails, then more messages, more emails, eventually got a guy who said he would take care of it, week went by, called again, left messages, got another guy from austrailia who appeared to be visiting, said he would ship next day, never saw anything , finally called tech support at woodcraft and asked if they had a contact to a manager at technitool cause i was about to throttle someone... they called and got the first guy to call me and he finally got the screws shipped...

if it was this hard to replace a stripped allen screw for a chuck, what happens when the cpu goes out in my lathe?

Re: Chuck

#4

Jesper, Denmark

Re: Chuck

Jesper, Denmark

The Allen head screws can't be anything very special - tool manufacturers don't re-invent screws. Measure it and find an identical screw locally. most likely, it's metric, so an aut supply store will have them, as most fasteners in the auto industry have been metric for ages.

If you do not have accurate measuring ability, just bring the old screw or one that is still good.

Buy a few extras - they are a bitch to find when you drop one in a pile of shavings DAMHIKT.

Re: Chuck

#6

Re: Chuck

John Veerkamp

Any hardware store that carries Hillman products will have the screw you need. As was said , get several spares.

John

Re: Chuck

#7

Re: Chuck

Jorge Castañeda

Don they are very standard, you can get the screws in any hardware store.

Re: Chuck

#8

Re: Chuck

Carole Valentine

You can get screws of the right length and thread, but I have never been able to find ones with the proper shaped head to fit the countersink in the jaws correctly. Maybe I could have if I were in the big city, but at the time Teknatool told me that they were made specifically for their chucks.

Re: Chuck

#9

Mike Mills

Re: Chuck

Mike Mills

From the way I read your question...you are talking about the #23045 Machined Cast Pinion. This is what the T wrench goes into to tighten/loosen the jaws. This part number if for the SN2.

They should have them at the service center data given in prior post.

Re: Chuck

#10

Re: Chuck

Don at Central Illinois

That is what I'm looking for. Called Technatool and left a message. I'm needing a schematic of the chuck to know how to dismantle, repair and reassemble. Hopefully they'll call sometime today.

Re: Chuck

#11

Re: Chuck

Jorge Castañeda

Carole, you may be right, I did not register where they go, and thought they were the grub screws which easy to fund.

Re: Chuck

#13

Re: Chuck

Carole Valentine

Very easy to do. You just need clip pliers big enough for the circ-clip. Don't mash the backing plate down too tight when you reassemble.

Re: Chuck

#14

Re: SN2 chuck assembly

Don at Central Illinois

That is just what I need. Now to order the part. I hope they can send it faster than they answered the voice mail from earlier today. Thanks again to all for the help.

Re: Chuck

#16

Dick Hines

Re: Chuck

dick hines

After you chanhe the pinions chunk the "T" wrench in the trash and get a 10mm wrench with out the other ball on the end.

Re: Chuck

#17

Re: Chuck

Carole Valentine

Just grind the ball off.

Re: Chuck

#18

Dick Hines

Re: Chuck

dick hines

Well you could do that but I just happened to have a "T" wrench that was 10mm. The one with the ball does not get a good bight. The ball works great when you have to work at an angle but I don't see why you would have to do that with a chuck..

Re: Chuck

#19

Re: SN2 chuck assembly

Don at Central Illinois

Thanks all. I received my part yesterday and with the help of the link provided, got it changed and cleaned the chuck in about 1/2 hour. Now to cut the knob off the tee handle and I'll be set. Again, thanks for all the help. I knew I could count on WC'ers to help.