Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Anybody use or made a bowl saw? *LINK*

Posts

Anybody use or made a bowl saw? *LINK*

#1

Anybody use or made a bowl saw? *LINK*

Craig Daymon

I was doing a general google search on "woodturning" and came across a site for a tool called the "BowlSaw". It seems simple enough. He has welded a section of saw blade onto the end of a steel rod and put a handle on it. It's a relatively inexpensive way to save bowl cores.

It looks like he gets in there pretty far with a gouge before using the saw. I'm guessing that you could probably give the core a firm smack and it would break loose without the need for the saw, but that's just a guess.

I put the link to the page below.

-Craig


The BowlSaw

Re: Anybody use or made a bowl saw? *LINK*

#2

Re: Anybody use or made a bowl saw?

Randy Gleckler

Might do a search of the archives on this. This was a VERY hot topic a while back on this site. Several used it and the owner even talked here a bit.

Re: Anybody use or made a bowl saw? *LINK*

#3

Dick Hines

Re: Anybody use or made a bowl saw?

dick hines

Didn,t know they were still making them. It's been a long time since i have seen one of these.

Re: Anybody use or made a bowl saw? *LINK*

#4

Steven Antonucci

Last time we traded e-mails...

steven antonucci

he said he had discontinued production of the Bowl Saw. I reviewed it, and it worked much better than I expected it to work. The shape issue was the main reason I think it never took off. Very limited.

You are correct that it was a piece of a sawblade welded to a rod.

Steve

Re: Anybody use or made a bowl saw? *LINK*

#5

Re: Anybody use or made a bowl saw?

Fred Holder

I published an article by Richard Steussy on his BowlSaw in the November 2008 issue of More Woodturning magazine. I also have one of the tools and have had the opportunity to try it out. I must admit that I had some reservations about this new tool. I found that they were unfounded. It actually works as Richard says it does. It is designed to core smaller bowls that the larger coring tools would not handle. So far, I’ve only cored one small 5 inch bowl with the tool. It is easy to use and doesn’t seem to be dangerous

if used as he describes in the article that he wrote.

It is not suitable for coring large bowls because the saw is not long enough to cut to the center on larger bowls. I thought a bowlsaw for larger bowls would be too unwieldy to use and probably would be “an accident waiting to happen”.

However, Richard says that he has developed one to handle eight inch blanks and that it works just as well as the smaller one. However, if you wish to core an eight inch blank and then core the core, you will need two tools the one that tried out and the new one designed for eight inch bowls.

If you are turning bowls in the five to maybe six inch size from exotic woods that cost a considerable amount, this tool may save you some money and get one or two additional bowls out of the piece of wood.

ations or from Amazon.com.

I recommend the BowlSaw as a way to save money and shavings

on small blanks.

Re: Anybody use or made a bowl saw? *LINK*

#6

Harry Robinette

Re: Anybody use or made a bowl saw?

harry robinette

The McNaughton company now makes a mini set that can work on a mini lathe or larger lathe to core out smaller bowls.

Re: Anybody use or made a bowl saw? *LINK*

#7

Re: Anybody use or made a bowl saw?

Ron McKinley

As Fred says, it works very well for small blanks of expensive wood. That's what Dick designed it for. He has quit advertising the Bowl Saw but I think you can probably still get one...........Ron

Re: Anybody use or made a bowl saw? *LINK*

#8

Re: Anybody use or made a bowl saw?

Craig Daymon

Thanks for all the responses.

It does strike me that the required technique is not that different from the Stewart Slicer. The saw itself replaces a sharp rap on the center section to free it, but other than that it is the same. I suspect it will typically result in more mass at the base, though it does reverse which section is impacted more by the process. The inside piece in the case of the Stewart or the outside in the case of the saw.

In the video, it does appear that he managed to somehow undercut the center section before using the saw, based on the size of the resulting cut tenon relative to the diameter of the removed section. It doesn't say how he accomplished that.

I think his choice of a straight saw section welded to the end wasn't the best. How about a flush cut, flexible, saw blade directly extending from the end of the shaft? It could follow any contour (remembering that the outside section is not yet cut to final finish) and flexing across the bottom, still accomplish the task.