Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Parting tool video *LINK*

Posts

Parting tool video *LINK*

#1

Parting tool video *LINK*

John Lucas

I'm still trying to do the short videos on specific tools. This one covers the parting tools and how I use them. Hope it helps someone.


http://www.youtube.com/watch?v=9W2m9JCG6IY

Re: Parting tool video *LINK*

#2

Re: Parting tool video

Ed Larson

Your videos are most informative and helpful.

However with your newer videos (this one and the one on skew practice for example) I get no sound when I plug in my ear buds or try to use the external speaker on my monitor. For you older videos (Wine stopper and Sharpening Tips for example) I do get sound from my ear buds and external speaker. To date your videos are the only YouTube videos that do not have sound with my ear buds. Have any others had trouble with the audio??

Keep the excellent videos coming. The sound problem is no big problem as I can hear them through the computer speakers but my wife is not into turning and prefers I use the ear buds.

Re: Parting tool video *LINK*

#3

Re: Parting tool video

Charlie Drake

John, as usual, very informative. Thanks for taking the time to produce these videos-especially helpful for those of us who have a long way to go before we consider ourselves accomplished turners.

Re: Parting tool video *LINK*

#4

Re: Parting tool video

Chuck Bjorgen

Excellent, as usual, John. I always learn something new from your tutorials.

Re: Parting tool video *LINK*

#5

Re: Parting tool video

John Lucas

I have not had anyone else mention audio problems. I not computer savvy enough to have any idea what to do about it. I'll look at the settings and see if I can figure out anything.

Re: Parting tool video *LINK*

#6

Re: Parting tool video

George Van Beynen

Very informative and thorough John. I like your Morse taper gauge. I did not have any sound problems on my laptop.

Re: Parting tool video *LINK*

#7

Re: Parting tool video

john lucas

The morse taper guage was from Mark StLeger. I use it all the time because my Nova Live center takes very short morse taper accessories. I just turn a full size one and cut it off. then I can drive it in the headstock and make whatever adaptor I need for my live center.

I started to turn a regular long taper with cuts every inch but decided that would take too long.

Re: Parting tool video *LINK*

#8

newbie questions

Ricc havens

John, as a newbie I really appreciate your videos. I had no problem with sound on my desktop

When you have time can you do a short "sharpening the parting tools" video?

Do you use a homemade jig or something?

I have trouble keeping a straight edge across the tip of my 1/8" diamond parting tool.

Thanks

Ricc Havens

Elkhart, IN

rv.havens AT gmail.com

Re: Parting tool video *LINK*

#9

Jim Evans

Re: Parting tool video

Jim Evans

Ed, if you get sound to your speakers, then the problem is on your end. Sometimes when I can't get sound from my ear buds, I plug into the headphone jack instead of the mic jack. ;~(

Re: Parting tool video *LINK*

#10

Dick Hines

Re: Parting tool video

dick hines

John, I like Ed have no sound but only in the right side. I have checked the head set and it works OK with other videos.

Re: Parting tool video *LINK*

#11

Re: Parting tool video

Mike Rubes, Apex, NC

Hi John,

That was nicely done and informative. Thanks for posting.

I like the morse taper jig as well, very creative.

Thanks,

Mike

Spinning tonight in Apex, NC

Re: Parting tool video *LINK*

#12

Re: newbie questions

john lucas

I may have covered that in one of the sharpening tips videos but it's really easy. Start with the lower corner of the bevel on the stone. Lift the handle until you see sparks come over the tip. do this very gently you don't need any pressure at all on the tool. then you simply watch the edge and rotate the handle until the edge is square. It helps to stand directly in line with the tool. Your stereo vision will kind of see both sides of the tool so it's easier to hold correctly.

It reality it doesn't matter much unless its way off. I have played with having a pretty extreme angle on the tip just to see if it cuts better.

I didn't go over the fluted parting tools because I don't own any.

Re: Parting tool video *LINK*

#13

Very informative. I like it


Re: Parting tool video *LINK*

#14

Jesper, Denmark

Re: Parting tool video

Jesper, Denmark

Hi John,

Well thought out and well presented - as usual.

Re: Parting tool video *LINK*

#15

Mike Stafford

Re: Parting tool video

Mike Stafford

All of your videos are very instructional and useful, John, and this one is no exception. Thank you for doing them.

I love my Sears parting tools and my Crown 3/16" diamond parting tool. I use the larger parting tool to taper the flange on the body of my box to determine the initial lid fit before I hollow the body. Then I roll the "crown" on the flange after I hollow the body to get a jam fit so I can turn the lid. The diamond shape lets me roll the cutting edge right up against the body and get a clean shoulder.

I can't wait to see what's next in your video series. This is like going to the movies and watching a Buck Rogers serial.....

Re: Parting tool video *LINK*

#16

Re: Parting tool video

john lucas

My Rocket has flames that go up instead of back, just like Buck Rogers. I hear there are drugs for that problem nowdays.

Re: Parting tool video *LINK*

#17

Mike Stafford

Re: Parting tool video

Mike Stafford

John, that is funny and proves that you are old. You have to be if you remember the pitiful special effects from the old serials.

My rocket only seem to go down these day and it no longer produces flames.....

Re: Parting tool video *LINK*

#18

Re: Parting tool video

john lucas

Mike You just need the right starter :)

Re: Parting tool video *LINK*

#19

Re: Parting tool video

Ron McKinley

Excellent John! ........Ron

Re: Parting tool video *LINK*

#20

Keith Tompkins

Re: Parting tool video

Keith Tompkins

Good Job John, I have several sears parting tools as well. Say what you want, they work great.