Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

my first "planned re-hydration project"

Posts

my first "planned re-hydration project"

#1

my first "planned re-hydration project"

mjonesrdg

In a post several weeks ago, I spoke of past successful experience with 'saving' over-warped and/or, cracked turnings. I will share with you in pictures below, my experience with planning to re-hydrate in advance, and not just using the process as an afterthought.

From my wood pile, I chose a real challenge.


This cherry chunk had the prerequisite cracks running through and through. It also featured an infolded bark inclusion, some punk, and a diagonally positioned knot.



The checks are wide enough to (normally) cause me to reject the piece outright.

As I hoped, the cracks swelled up tight after soaking in plain water for about 6 hours. Ca glue was introduced into the cracks, and also, as hoped, made "hairline" cracks which you can see if you study the finished form.


So, it's not a "museum" piece, wouldn't pass muster at a juried show, and not likely going to an up-scale gallery. But I think that someone will enjoy having it on a shelf at their home.

Finished size is 7" high and 8" wide. Finished with CA Medium and buffed/waxed.

There have been a few suggestions from other turner's correspondence that merit trying also. I'll let you know if I have more to share.

Mike Jones, in Redding, California

Re: my first "planned re-hydration project"

#2

Re: my first "planned re-hydration project"

bernie feinerman

Did you re-hydrate the wood before you turned the bowl, after you had roughed it out, or ????

At what stage in the process was the CA glue "introduced" into the cracks?

While the bowl might not be museum quality, it is certainly a beautiful bowl.

Bernie

Re: my first "planned re-hydration project"

#3

Steven Antonucci

Dumbstruck at how well that appears to work!

steven antonucci

I would have never guesses it would close a crack that big...

Turn, soak, glue, turn?

Steve

Re: my first "planned re-hydration project"

#4

Re: my first "planned re-hydration project"

George Van Beynen

One more looking in amazement!

Re: my first "planned re-hydration project"

#5

Re: my first "planned re-hydration project"

John Lucas

I'm impressed also. I'm a little concerned how long it will last so I hope you keep us up on it. I will definitely give it a try sometime.

Re: my first "planned re-hydration project"

#6

Rob Wallace

Can you give us an idea.....

Rob Wallace

..... of how much time elapsed between the soaking/rehydrating and when you finished the piece? Information about the conditions of "the second drying"? Did you do anything (i.e. make weight measurements, use a moisture meter, etc.) to determine when it was ready to finish?

It is likely that you have not added any 'bound water' to the wood with a relatively short soak, but I am curious to learn about how fast the 'second' water loss took relative to the time spent drying during the original water loss, and how the rehydration effects (e.g. creates, releases, or disperses) stresses in the finished piece (other than just closing cracks which are then subject to you CA gluing treatment).

I think this kind of experimentation has merit, however some sort of controlled comparisons need to be done to be able to draw cause and effect conclusions rather than amassing anecdotal evidence.

Very interesting, to say the least!

Rob Wallace

Re: my first "planned re-hydration project"

#7

Re: Can you give us an idea.....

mjonesrdg

The cherry chunk was three years dry to start. I roughed turned the form to 1/2" wall, and sunk it in a bucket. When I saw the cracks closed up, I blew the cracks and surface with compressed air to drive out excess water and started gluing within the hour. The piece sat to air dry one day and registered 14% MC the following day. I then improved the shape, formed the rim and took the innards down to 1/4" wall. From there, the CA med was spread over the outer surface to seal it up. I didn't get to any interior application with the CA until the following day.

I'm too old to make a reasonable effort at scientific results....maybe one of the younger turners could take the ball from here.

Re: my first "planned re-hydration project"

#8

Re: my first "planned re-hydration project"

Carole Valentine

Beautiful form, Mike. Be interesting to see how this piece holds up over time with normal shrink swell cycles from changing humidity. Personally, I think there is too much decent wood out there to go through the hassle (and possible risk) of doing this to turn badly cracked wood. But that's just me. I keep thinking of all the cases where bowls have exploded on the lathe due to unseen cracks, much less visible ones! One thing that determines whether or not I will continue turning a chunk of wood is the sound...there are subtle changes in tone that help to tell me if the wood is unstable. I think this rehydration process would hamper that sense. Call me a chicken, but my faceshield does not have any scars on it...yet. :)

Re: my first "planned re-hydration project"

#9

Brad Vietje

Re: my first "planned re-hydration project"

Brad Vietje

Um.... yeah -- what she said. You created a beautiful turning, Mike, but any thoughts about the danger of one of those glue lines splitting open?

Or, just being funny for a sec: "You'd have to be CRACKED to do that!"

I'll be interested to learn about how it holds up.

Safe spinning,

Brad Vietje

Newbury, VT

Re: my first "planned re-hydration project"

#10

I have 2 thoughts on this

john lucas

First is, thanks for posting. I think a lot of people will give it a try. For some reason we are drawn to a piece of wood and want to save it no matter what. maybe it's our cheap nature, maybe it's just having trouble finding good wood, or maybe it's just not wanting to admit defeat.

The other thought is, every time I repair cracks I can always see them and it bugs me. The vessel I just did had cracks in it. I thought they would turn away because they looked to be on the surface. Once I got into the bowl I thought they were just on the outside and I was going to texture that vessel anyway. Then when I got inside I realized they were deep. I filled them and continued. I don't like it now because to me the cracks are obvious. No one I've shown it to has even asked about them so it must not bother them.

So I guess what I'm saying is, you really should try to use wood that doesn't have cracks. the piece will just look better. However if you persist (and I probably should include myself) then this seems like a very good method to try. Long term results may change that feeling we'll have to see.