Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Hunter tool

Posts

Hunter tool

#1

Hunter tool

Starry S Chan

I have a carbide cutting tool similar to the Hunter #4 tool. It has a round shaft and a round cutter. I tried it once to make a finishing cut on the outside of a bowl and I got a big catch. I remember watching a video segment with John Lucas demonstrating this tool. However, I can no longer find this video.

If you have experience using such a tool, please share with me the proper technique in making the cut.

Thanks,

Starry

Re: Hunter tool

#2

Re: Hunter tool

Fred Holder

If it is a Hunter Tool with the round carbide cutters, the tool should be rotated to apply the cutter at a 45 degree angle to the wood. If this is done, the tool should cut cleanly and not catch.

If it is a Eliminator tool, which uses a cutter similar to the Hunter Tool, but has a larger round shaft that is milled with two flats on the shaft. Each flat area applies the cutter at a 45 degree angle to the wood. If used correctly, it seldom ever catches.

If the tool is a round cutter like the Easy Finisher, the tool should be applied level with the center of rotation. That is the one thing that makes it easy for new turners to use the Easy Rougher and Easy Finisher. There is no rubbing the bevel and the tool is applied straight in on dead center of the axis of rotation.

Re: Hunter tool

#3

Re: Hunter tool *LINK*

John Lucas

Starry The link to Mike Hunter's website is below. All of the video's I've done on the Hunter tools are there.


http://www.hunterwoodturningtool.com/

Re: Hunter tool

#4

Don Leydens

Re: Hunter tool

Don Leydens

Hi Starry! Please keep in mind that if you have a different cutter than Mike Hunters it's not going to cut the same way. Mike's cutters have a "cup" shape to them. Most other cutters I've seen are flat on top and just aren't the same quality at the business end.

Re: Hunter tool

#5

Re: Hunter tool

Ken Vaughan in Juneau Alaska

My experience was with the Hunter #6 that woodcraft sells. The cup cutter is mounted on a massive round steel bar and the mount is level and near midline of the bar. I got it because that was what was in the store when I decided I needed one for a bowl that was a bit big for a midi lathe.

I had some problems with the tool as I wanted to use bevel riding cuts and the tool tended to roll. I use a file to put some flats near the tip at about 45 degrees from verticle and it gave me enough purchase on teh toolrest for stability and the rolling stopped along with the profane words.

If you are trying to use the tool at an angle and it is not stable, try a small flat on the around bar.

Re: Hunter tool

#6

Re: Hunter tool

John Lucas

The tool works wonderfully when rubbing the bevel at the tip. You can't rub the bevel on the side the tool will twist. Any tool will when used this way if your not very careful.

Re: Hunter tool

#7

Lyle Jamieson

Re: Hunter tool

Lyle Jamieson

The John Lucas clip can be found through Mike Hunters Website. www.hunterwoodturningtool.com, go to Tutorial menu, look for Lucas general use video.

You said "similar" to Hunter. All carbide cutters are not created equal. The wide range of carbide quality and presentation angles makes it pretty confusing. Some need to be used for shearing/slicing cutting, some used for scraping only, some good for roughing, some can be used for finishing. If you understand the dynamics of turning you will never get a catch with any tool, carbide or otherwise.

Let me define some things. All slicing cuts must have the bevel support. All scraping cuts must be presented to the wood at less then 90 degrees. It's just that simple. Once you obey the rules you don�t get catches. My "Bowl Basics The Easy Way" DVD is in most turning club libraries. It covers all the foundations needed to turn safe and fun. I use the bowl format to instruct how to have complete control and never get a catch again. I use a bowl gouge from start to finish in the bowl, but the same rules apply no matter what tool you have in your hand.

As most turners realize early on in the learning curve they need some help to improve tool control. It is a lot of trial and error, and the errors lead to fixes that might not be very dependable and create obstacles to fun and creativity. You have turning club members near you that would be willing to mentor you in tool control, just ask. Your question is revealing. I hope your experience with the carbide cutter leads you to greater insights on tool control with all of your turning tools.