Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

New Thompson tools for Lauren

Posts

New Thompson tools for Lauren

#1

Alan Zenreich

New Thompson tools for Lauren

Alan Zenreich

I haven't seen any photos of this new toy on this forum, so I figured it would be nice to show it off.

I surprised my bride the other day with a gift wrapped item.

She eagerly unwrapped it, and was delighted to see her name on it (special thanks to Doug for being able to 'cross' the Z in our last name.)

However, she was a bit confused why I would just get her a handle.

She rattled it a bit and began unscrewing the bottom. I said 'that's where you put the batteries'.

She's not that gullible, but did give me an evil grin as she kept unscrewing the bottom plug.

Out came the four 3/8" V10 bits and a hex wrench.

Three bits came preground... bowl gouge, spindle gouge, detail gouge. One came round/fluteless... it can be ground into any shape desired (perhaps a skew, or a point tool, or a skewchigouge-like point)

So, I'm one of those fortunate few who can actually buy tools as gifts for the lady of the shop.




Re: New Thompson tools for Lauren

#2

Alan Zenreich

Re: New Thompson tools for Lauren

Alan Zenreich

Not being one to leave well enough alone, I decided to make replacing the bits a tool-less operation.

This is a first attempt at a T handle to replace one of the setscrews of the 12" handle.

Thought you all might be entertained, by my little, simple tweak.

The steps

�I drilled out a 1/4x20 female thread T-handle and rethreaded it to 5/16x24

�On a mini-lathe, turned the head of a 5/16x24 socket head bolt to reduce the diameter, allowing it to fit inside the top opening of the T-handle

�Shortened the socket head bolt to the proper length

�Threaded the bolt into the T handle, using some red Loc-Tite (I can always install a horizontal pin if necessary later, but I don't think it will be needed)

The remaining set screw is just barely snug to the insert

The T-handle only needs finger pressure to secure the bit.

So far, so good.





Re: New Thompson tools for Lauren

#3

Re: New Thompson tools for Lauren

Curt Stivison

If the women don't find you hansome they should at least find you handy.

(RED GREEN QUOTE)

Very nice set of tools. Hope she remembers this when it's your birthday.

Re: New Thompson tools for Lauren

#4

Alan Zenreich

Re: New Thompson tools for Lauren

Alan Zenreich

We generally don't give each other gifts on our birthdays. We usually say "this is your birthday gift" when we buy something (usually pricy) a few months before or after a birthday... sort of an excuse for the money already spent.

This was kind of fun because this gift arrived exactly a month after her birthday arrived.

Then again, we used to send out New Years cards... March. We didn't want ours arriving in the same mail as the card from your insurance agent.

So,when you least expect it...

Re: New Thompson tools for Lauren

#5

Steve Kubien

Re: New Thompson tools for Lauren

Steve Kubien

I got to oogle this kit at Chez-Mushinski a couple of days ago. Initially I failed to see the real point to such a kit but when Steve pointed out that he does often travel with tools, I suppose I understood better. Since that time I have also considered all of the mini-lathe owners out there and figured this would make a great intro kit.

I think I need a couple more handles....

Re: New Thompson tools for Lauren

#6

Alan Zenreich

Re: New Thompson tools for Lauren

Alan Zenreich

Steve, I agree.

Much of what Lauren turns are small items (jewelry, etc) and these are a good size for that kind of work. She'll keep the bits in a rack, and because it's now trivial to change bits, only one handle is needed.

Also, removing the bit from the handle does facilitate sharpening.

So, she's delighted.

Re: New Thompson tools for Lauren

#7

Steven Antonucci

you missed my birthday...?

steven antonucci

but then again, so did I...

I am sure that she will be very happy with her 10V's, but did you know that Doug's selling 15V's now too? 5 more V's betterer... :D

I wonder if I unscrew the handle on my gouge if there are 4 more gouges inside? Perhaps I should do it upside down so they can all fall out in unison? 8)

Tell her I said happy birthday and thay she should turn some space inspired jewelry quickly to get into the NJW challenge!

Steve

Re: New Thompson tools for Lauren

#8

Alan Zenreich

Re: you missed my birthday...?

Alan Zenreich

Steve,

Go ahead and unscrew the plug from yours. You might want to be ready to pick up all the shot that falls out.

As for getting extra 'V's for Lauren, that will have to wait... Doug isn't supplying them in this size yet.

Re: New Thompson tools for Lauren

#9

Steven Antonucci

You mean my handle isn't filled with 10V gouges...

steven antonucci

I'll have to call Doug :)

You will have to upgrade to the more V's model later. I cut black locust last night at the WGW meeting without sharpening (2 hours... :D)

S

Re: New Thompson tools for Lauren

#10

Re: New Thompson tools for Lauren

John Lucas

Steve This is a new kit that Doug is offering for the beginner turner who doesn't have any tools. It's gives you a bunch of tools all in one package. It is meant to keep the cost down on getting started. There are actually 5 tools. The skew has a point tool on the other end.

Re: New Thompson tools for Lauren

#11

Alan Zenreich

Re: New Thompson tools for Lauren

Alan Zenreich

John,

According to Doug, he's providing the 4th blank... well, blank (not ground at all), so people can put whatever shape they want on it themselves.

The configuration shown above is how it arrived. I asked if this was intentional (hopefully) or a happy mistake. He confirmed that it is as designed.

Re: New Thompson tools for Lauren

#12

Re: New Thompson tools for Lauren

Doug Thompson near Cleveland

These only have the 4 tools because if I sharpen a tool on both ends the one side is against the aluminum end cap. The set has been to popular... about to run out of tools for this set. I'll put it officially on the site next week.