Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Needle Scaler

Posts

Needle Scaler

#1

Needle Scaler

Barry

I've heard of people using needle scalers to apply surface texture to turnings. At my local Harbor Freight, they have two of these tools, one a mini version and about half the price of the other. I'm thinking the smaller might be more useful. Any comments, or experiences? Thanks.

Re: Needle Scaler

#2

Re: Needle Scaler

Ed Moore in SW VA

Bob Rosand is an advocate of the needle-scaler. I use one to texture the roof of my acorn birdhouse ornaments that are like Bob's. I have both of the Harbor Freight models and now use the smaller one exclusively. For textruring, the smaller one is quite adequate.

Remove the needles from the device and round over the business ends of the needles. This way you get dimples instead of sharp cuts.

Ed

Re: Needle Scaler

#3

Re: Needle Scaler

Jennifer Indy.USA

I use a Harbor Freight one that is quite cumbersome. It attaches to an air hammer by screwing onto the end of it. I may have to check out this mini one you're talking about.

Jen

Re: Needle Scaler

#4

Re: Needle Scaler

Greg Haugen

Barry,

The compact or "mini" needle scalers are what you want. The versions that are full size or attach to air hammers are a pain in the butt. As Ed mention, you'll want to disassemble the head of it and round over the tips of the needles. Sioux's mini scaler is the top of the line scaler and the one Rosand wrote the article about in the AAW journal a few years ago. However, the compact or mini scalers from harbor freight or northern tool would work just as well. The smaller the model you get, the easier and less cumbersome it will be to use.

Re: Needle Scaler

#5

Steven Antonucci

How much is the little one?

steven antonucci

I haven't been able to find one? I saw a "professional one" that was way more than what I was willing to spend. Perhaps a mini is more up my alley?

Thanks

S

Re: Needle Scaler

#6

Re: How much is the little one?

Greg Haugen

Sioux's Mini Scaler are usually $80-$130 depending on where you buy it and sales. I've bought one locally for $60 during a sale at our welding supply shop. Harbor Freight's compact is currently on sale for $28, normally $30.

Re: Needle Scaler

#7

Compact Harbor Freight Needle Scaler *LINK*

Ed Moore in SW VA

The link to the Harbor Freight needle-scaler is below.

Use the needle scaler on end-grain. On bowl orientation you will get an irregular pattern dues to changing grain orientations.

Ed


Harbor Freight compact needle-scaler

Re: Needle Scaler

#8

Re: Needle Scaler

dick gerard

To make the HF needle scalers less cumberome, cut the needles down by 1/3 or so. Makesthem easier to conto. Also, comsider leaving out one of the 12 needles ... gives you more control and a subtler dimple.

Re: Needle Scaler

#9

Needle Scaler pictures

Ed Moore in SW VA

I took a picture of a birdhouse roof, which is less than 1 1/2" in diameter.


And here are the two different needle-scalers. Note the rounded ends of the needles.


Ed

Re: Needle Scaler

#10

Mike Stafford

Re:  Needle Scaler pictures

Mike Stafford

Ed, do you use these needle scalers during your class? Does the school compressed air system supply enough ooomph to power them?

Are there any woods which you have found to be too soft to use this tool on?

Re: Needle Scaler

#11

Re: Compact Harbor Freight Needle Scaler

Greg Haugen

I've never have had an issue with end grain or face grain. I've scaled bowls and vessels. The beauty of this tool is that it is hand held. If a wood is softer, hold it lighter. If it's end grain or denser, lay into it. :-) Some don't like the texture and says it's "too much" so they get a similar effect with a 16 penny nail in a reciprocating carver.

Re: Needle Scaler

#12

Re:  Needle Scaler pictures

Ed Moore in SW VA

Hi Mike,

JCCFS has plenty of air pressure in their system. The needle scaler was easy to use there.

To be honest, the only wood that I have used them on is mahogany, because that is what I use for the roof on the birdhouse.

Ed

Re: Needle Scaler

#13

Dremel engraver

john lucas

Barry You might also look at Dremel vibrating engravers. I think Sears sells one also. Take the pointy bit out and install a rounded over 1/8" piece of steel. I use the shank of old drill bits. The you have lots of options. you can just scribble. you can make patterns. You can make lines. There are lots of options. Mostly what I do is sort of random scribble. It leaves a texture similar to the needle scaler depending on how you use it. It's also very easy to put a pattern inside a couple of turned or burned lines. that's something that's difficult to do with the needle scaler. The needle scaler is far faster for doing large surfaces.

Re: Needle Scaler

#14

Leo Cuellar

Harbor Freight Needle Scaler

Leo Cuellar

I have one of the mini needle scalers. I can tell you that it is one tough little puppy. I ran it for almost 8 hours straight removing rust on steel & it showed no signs of slowing down or wear on ends of the needles. Should work well on wood, but haven't had a project to try it yet.

Re: Needle Scaler

#15

Re: Needle Scaler

Dick Coers

The mini scaler is the one to buy. I have one set of needles that I rounded over. I took out the needles, put them in a cordless drill, then ground the ends round. I have another set of needles that I ground to a 45 degree angle for sharp impressions in the wood. I have a third set of needles that I hollow ground the ends so it makes a fine circular dent in the wood. I put those needles in a drill chuck on the lathe, then used a tear drop diamond burr in my dremel to hollow grind. I love them.