Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Question on vernier scales

Posts

Question on vernier scales

#1

Question on vernier scales

john lucas

I have to make a multi sided walnut vase that matches the bottom of a stool. For lack of a better description lets call it 16 sided with a flute that fills each segment from top to bottom. Here's my problem. I have an index wheel and I think it might be hard to get the index to line up properly with the center of each segment.

Several times I've thought it might be nice to put a short pin on the backside of my chuck that would fit in a hole in the index wheel so when you install it, the index wheel would be in the exact position each time. You could take the chuck off the lathe for other carving details and then put it back on and index it exactly the same.

Now, I would like to drill several holes in the back that work like a vernier scale. In other words if one hole didn't line up exactly I could just try another one. Does anyone know how you would calculate this? I think you could mark off say 16 distances we'll call X. Divide one of those distances by 10 which I'll call Y . then you would drill a hole, rotate the chuck x+Y and drill another. The next hole would X+Y+Y, then X+Y+Y+Y, etc. do yo think that would work?

Re: Question on vernier scales

#2

Re: Question on vernier scales

Bruce Pratt

John,

Can you provide a picture of what you want to do? I can probably help from there.

---------

Bruce

Re: Question on vernier scales

#3

Re: Question on vernier scales

john lucas

Bruce Can't provide a photo today. What I'm trying to do is to make some sort of really fine adjustment to how the index wheels attach to the lathe and chuck so that you can orient a router exactly where it needs to be to get the cut. You can't drill holes that close together in the back of the chuck to use a pin but I think you could drill them around the back using the same kind of divisions found on a vernier caliper.

Re: Question on vernier scales

#4

Re: Question on vernier scales

Galen Vetterick

The indexing plate is held on by the chuck? The drilled pin hole in the plate and chuck would always line the two back up as you noted. Then why not just align one of the piece sides with the first indexing hole. Infinitely adjustable in the jaws. Is it just the sides are yet defined when you first chuck it? Do you just need some type of pointer installed in the indexing wheel to help align one side to that first hole? Laser pointer in one indexing hole?

Re: Question on vernier scales

#5

Re: Question on vernier scales

john lucas

Galen It's trial and error to get one of the index holes to line up exactly with the cut. sometimes you get lucky. I've tried loosening the chuck and shifting the index wheel then retighten. again sometimes you can and sometimes you can't. That's why I wanted a more consistent solution.

another solution that just hit me was to make the index pin adjustable. If I make an L bracket to fit the lathe with the pin height adjustable via a screw type mechanism I could have an almost infinitely fine tuneable index wheel.

Re: Question on vernier scales

#6

Re: Question on vernier scales *LINK*

Dick Coers

Here's the way one guy does it. Check on rose engine designs John. I think that you could also make something like a single hole for the pin, but have that mounted on something like a protactor. Pivot the protractor by partial degrees, and then clamp it down.

On the second link, scroll down to the 4th article and he shows a graph for a two plate venier.


http://www.ornamentalturners.org/Resources/article

Re: Question on vernier scales

#7

That didn't work so well. *LINK*

Dick Coers

Here is the second link.


two plate venier

Re: Question on vernier scales

#8

Thanks Dick

john lucas

That's exactly the concept I had in mind Except I thought I would make the chuck the second plate so things would always register with the chuck and consequently whatever is in the chuck. I'll read it over more closely tomorrow and make some sketches.

Re: Question on vernier scales

#9

Re: Thanks Dick

Barry Irby

I like the idea of making the pin adjustable, I think. (It might make it unreliable and so that when you were using it for something else it would be out of whack because you had adjusted the pin.)

How about making the router adjustable? Could you rig it up so you could side slip it a little to calibrate it to the center?

Re: Question on vernier scales

#10

Re: Question on vernier scales

DaveN

John,

The way a standard Vernier scale works is by dividing the space that ten divisions take into 9 divisions. What you would need to do is drill nine holes in your chuck to cover the same angular distance as ten holes on your index plate. That would effectively divide each index gap into ten.

Hope that makes sense.

Dave

Re: Question on vernier scales

#11

Re: Question on vernier scales

DaveN

Sorry John - got it arse-about-face.

You should drill ten holes in the chuck to match nine holes on the index plate.

Dave