Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Making a stand for my lathe

Posts

Making a stand for my lathe

#1

Making a stand for my lathe

Earl

OK folks I have a Turncrafter Commander with ext. I am making the table 12" wide by 60" long. I am using 2"x1/8" angle iron. I will splay the legs but that is the question for me. How wide do I need to spread them out? I want them out far enough to make it stable but I don't want to have them so far I trip over them. The lathe has little rubber knobs that it sits on would I be better off to blot it to the table or sit on the rubber knobs? Also when I get it settled where I will leave it should I bolt it to the floor (cement floor) or put a shelf and put sand bags to hold it down? Thanks for any help you can give a newbee Earl

Re: Making a stand for my lathe

#2

Re: Making a stand for my lathe

woodspinner-Harry Robinette

Earl

We made one for my buddy's 12 X 20 and splayed the front legs just a little and the back leg's splayed allot.

This let him put the weight on the back wide bottom part and keep the shelf for tools and chucks and stuff.

He said it works great. Just my $.02

Re: Making a stand for my lathe

#3

Re: Making a stand for my lathe

woodenleg

I would use either bagged sand or bagged lead shot in case you have to move it for some reason. You also might want to turn on it before you add the weight has some splayed leg units do not bounce. Dave

Re: Making a stand for my lathe

#4

Joe Fleming

Re: Making a stand for my lathe

Joe Fleming

Earl,

Twelve years ago, I made the stand that Woodsmith had in their magazine. I modified the dimensions to fit my lathe. It worked great. It was made from particle board and wood edge banding. I used poplar. It had a box in the base that I filled with sand.

Joe Fleming - San Diego

Re: Making a stand for my lathe

#5

Re: Making a stand for my lathe

john lucas

I built the same stand Joe Mentioned for my Delta Lathe. When I got the Nova 3000 I built one out of wood, mostly 2x4 and plywood. I think I used 2x6's under the bed of the lathe. It had a design similar to what is discussed above with the front being flat and the back being tilted out give a wider foot print. I filled it with sand. Sand is not a good idea. It leaks out due to the vibrations so I filled bags with sand. That was in improvement.

When I got the Powermatic I added weight in the form of bags of pea gravel. I think that has worked just as well as sand and hasn't even come close to leaking out of the bags. I did find some bags that look like the kind they use to make levees. They don't tear.

Re: Making a stand for my lathe

#6

Re: Making a stand for my lathe

Don Evans

I'm not familiar with that lathe so I don't know what size and weight we are talking about, BUT, 2" x 1/8" angle iron isn't seem strong enough. You may actually be better off building it from wood as it helps absorb vibration. If not, I would consider pipe, but although I can weld, I'd be concerned about my skill to get it level with no metal warp from the heat.

Remember that a round pipe is stronger than a solid bar and also it is extremely important that the bed of the lathe be level. Even the slightest twist in the bed will give you big problems with alignment and how much you will enjoy working on it.

On the angle, even a mini lathe 10" during rough out you may get a lot of vibration and actual bounce using that 1/8".

It's just like building a house, ya gotta have a good foundation before building upwards.

Re: Making a stand for my lathe

#7

Re: Making a stand for my lathe

Cyril Griesbach

Earl,

So far no one has addressed your question regarding the rubber pads now on the lathe. I would remove them and bolt the lathe directly to your stand.

Re: Making a stand for my lathe

#8

Lyle Jamieson

Re: Making a stand for my lathe

Lyle Jamieson

Earl, you have the right idea but need to beef it up a bit. Big footprint, mass, and leveling feet are a must. Done right a little lathe would work a lot better. The angle iron would work but thick square wall tubing is better. Using angle iron I would stiffen it by screwing a pannel of 3/4 inch plywood on three sides to stiffen it up. Make sure you leave a kick space in front so you can stand with your shins up close to the bed. While you are at the plywood addition, make a sturdy box under the bed to fill with sand. 2x2x6 feet box would give you a good volume of sand. Use a plastic liner to prevent leaking. Weld a nut on the end of each leg and put a bolt with the head down with room for a locking nut and you have your leveling system.

Re: Making a stand for my lathe

#9

Lyle Jamieson

Re: Making a stand for my lathe

Lyle Jamieson

Strongly agree. No rubber or soft landing anyplace.

Re: Making a stand for my lathe

#10

Re: Making a stand for my lathe

Dave Paine

I have a NOVA DVR 16in lathe. I made my own table/stand from wood.

I have 3in x 3in ash legs and 2in x 4in rails on the top and bottom.

I made my table 18in wide x 48 in long so mine is rectangular. Top is covered with two 2in x 9in x 48in pieces of hem/fir glued together and screwed to the top rails.

My bottom rails are about 4in off the floor to allow casters and space for my feet for close work. I have a shelf covering the rails. I was considering building a box for sand, but decided I would use the space for storing tools. I will get the weight and useful storage.

I bolted my lathe to the table. Highly recommended. I have not noticed any vibration issues so far.

Leveling is a must. I installed 3/8in dia steel leveller screws in each leg. My floor is not level due to being a garage and designed for draining any water.

I went with a rectangle shape to give myself some space on top to lay things down. This is proving very handy for me. Chucks, key, tool being used, etc.

I put casters on my recent tool tables/stands since I am not getting younger and whenever I tell myself I never need to move something, I eventually find things need to be moved for one reason or another, although infrequent. Putting the casters on during construction allows me to move if/when I need to without breaking my back.

Re: Making a stand for my lathe

#11

Re: Making a stand for my lathe

Earl

Thanks for the reply Don. I looked on the Penn State web site at the stand they sell for this lathe. It looks like their stand uses lighter material than 1/8". I think the 1/8" will be heavy enough with a little bracing. Earl

Re: Making a stand for my lathe

#12

Re: Making a stand for my lathe

Bart Leetch

Earl

What you have for angle will work just fine I used to have a bigger lathe on salvaged bed frame angle. What I did is splay the legs forward & back & I recommend the splaying back & just a little forward I also splayed mine toward the ends, which isn't necessary. I made my frame to come apart where the legs & top frame came together, I just left the web a little long on one side of the angle & drilled a hole in it for a carriage bolt & wing nut. The cross piece between the legs on each end had a bracket that a piece of angle fastened into & went from there to a bracket centered on the bottom of the part the lathe was mounted to. So from the legs you would have an inverted V this kept the legs in the correct position.

Re: Making a stand for my lathe

#13

Re: Making a stand for my lathe

Tom

I purchased the same lathe with the Penn State stand some months ago. Put 3/4 inch plywood on the top and shelf and casters on the legs (I attached a 2x4 cross piece to the legs on each end and then attached the locking casters)I removed the rubber bumpers and bolted the lathe to the top. It is very stable and easy to move around. Since this is a small lathe, I don't turn big stuff on it anyway so no vibration. One could put sandbags on the shelf if needed but I find the shelf useful for holding chisels, etc. rather than laying them on the ways (and have them roll off and land tip first!) Great little rig!

Re: Making a stand for my lathe

#14

Re: Making a stand for my lathe

Stuart Johnson

When bolting to the stand if possible use blocks between the lathe and the stand high enough to clean chips our from between the ways.

Re: Making a stand for my lathe

#15

Re: Making a stand for my lathe

Opelika Edro

Good call -- I bet I wouldn't have thought of that until it was already built and filling up!

Re: Making a stand for my lathe

#16

Thanks to everyone

Earl

Thanks to all for taking the time to help me. I have the legs welded to the table and everything seems solid but I am going to take the advice given here and do some bracing. I had not planned to put leveler's on it but I will take the advice given here and put them on. Again thanks to all and WoodCentral is the greatest. Earl