Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Q&D Steady Rests

Posts

Q&D Steady Rests

#1

Q&D Steady Rests

charlie belden

The President's Challenge for tonight's turning club meeting is TREMBLEUR - in english TREMBLERS - quite appropriate for California.

I've learned to turn long and thin ( if 1 1/2" to 2" can be considered "long"). But turning long and thin - between to short but FAT requires some way to support the FAT end so it doesn't start wobbling around - and snapping the THIN.

I saw a quick and dirty way to make steady rests that use string - in this case dental floss - to to dampen the FAT end's wobbling while you turn the THIN. Probably wouldn't work as well with larger, longer THINs with proportionately fatter FATs - but for littler stuff these things work great and can easily be made from scrap ply.

From chuck to tip what you see is a tad over 8 1/2". Ultimately this little trembleur will be about 10 1/2 to 11" tall.

Try it - you'll like it.


Re: Q&D Steady Rests

#2

Re: Q&D Steady Rests

John Lucas

charlie I made some string steady's for a project once and they work surprisingly well.

Re: Q&D Steady Rests

#3

Re: Q&D Steady Rests

chet.gelnett hp.com

did you use wax string?

Re: Q&D Steady Rests

#4

Steven Antonucci

Escoulen does this

steven antonucci

Watched him turn something at least 24" long and probably a little thinner with perhaps 4 of the string rests like you show. His were even less refined than yours, but his turning required very little sanding.

He let us touch it while he was turning, and it is remarkable how well it works.

S

Re: Q&D Steady Rests

#5

Re: Q&D Steady Rests

charlie belden

Tried waxed as well as dewaxed dental floss. The dewaxed floss was harder to handle since it's a bunch of very fine threads that tend to spread and unwind - making tying knots an exercise in fine motor skills - and requiring good eyes. Waxed floss is easier - for me. The wax may also act as a lubricant, reducing friction and potential abbrasion. At 1600 - 1800 rpms, I suspect the wax does melt or soften.

Oddly, things get more stabile at higher rpms.

Re: Q&D Steady Rests

#6

Re: Escoulen does this

charlie belden

The idea is not to GRIP the spindle, but rather to restrain/limit its movement

Because it cradles the part in opposing Vs, there's seems to be more continuous support than the wheels with single points of contact steady rests - which are more difficult to set up correctly.

I'm turning on a JET VS Mini - so the length I can turn is limited. I guess I could ass a bed extension - but that would require lengthening my bench to accomodate it. And THAT would put me farther away from the headstock when hollowing. With my current set up I can stand near the end of the bench when boring into or hollowing - no leaning over from the side to deal with. My back doesn't deal with extended periods of supporting my upper body when leaned over that far.

I may do one or two more trembleurs - just to see how small and long I CAN go. Not having done one before, I erred on the side of caution for the first section - and that dictated the diameter of the subsequent sections. The fact that I used a poplar dowel was also constraining - again erring on the side of caution. Were I to have had a straight grained maple dowel I would have been more adventurous.

Trembleurs are fun to do - though a tad nerve wracking at times. And when you get pretty thin - good eye sight and depth perception become crucial.

Re: Q&D Steady Rests

#7

Re: Escoulen does this

Barry Irby

I have a DVR which at the time didnt have a bed extension, so I could turn about 2' between Centers. I turned a nine foot long piece on it. Started with a piece small enough to pass through the headstock and set up a piece with a bunch of screw eyes on it to support he work and stop it from whipping. Passed it right through my chuck and used that to grip and drive the piece. Advanced it about 6" at a time. After I got it set up and working, it became sort of boring.

So, you can tuna trembler as long as you want, if it's small enough.

Re: Q&D Steady Rests

#8

Re: Q&D Steady Rests

jim rutten

Hi Charlie,

I was wondering if you thought looping the spindle would cause more support or just muck it up. My though being go from top left nail to bottom of spindle looping around and going to bottom left nail then across to bottom right nail to top of spindle and around knotting off at top right spindle. Kind of like opposing Os. Too much friction?

Re: Q&D Steady Rests

#9

Steven Antonucci

That's how Escoulen does it, Jim

steven antonucci

I reread Charlie's post, and it is different than how JFE showed me at Totally Turning.

His process was to start at 1, and loop around the spindle back to 1. Then go over to 2, loop around the 2 and then loop around the spindle back to 2. (same for three and 4. It creates 4 loops around the wood that each two opposite restrict the wood from deflecting in that plane. He used a waxed linen thread if memory serves me well...

S