Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

3520b resonance

Posts

3520b resonance

#1

3520b resonance

Rob Kennedy

Hi I hope someone can help I have had a new 3520b now for the last 8 weeks However it seems that when I do any kind of large bowl turning I get a vibration the bigger the cut the more vibration it happens at any speed I think I have tightened everything up as much as I can and the lathe sits on 4 concrete pads. I was wondering if I could put something between the legs and the bed to try and provide some dampening to stop it of is there something obvious I have missed? Is it my technique? I levelled the lathe very carefully and I believe its flat but I did notice that one of the legs is not quite flush with the bed. I like to turn thin walled stuff and this vibration (and noise) prevents me from doing so I really need to sort this out I have had so much trouble with my chuck and getting it to run true which I have finally sorted only to come up against this problem.

Any ideas or suggestions welcome I will try anything now to get it to work right everyone has extolled the virtues of this lathe but I seem to have been dogged with a few problems

Re: 3520b resonance

#2

Re: 3520b resonance

John Veerkamp

Rob,

I have this problem occasionally with my PM also. My floor is uneven and if the lathe moves any from the setup spot I will get vibration. I just need to make sure all four legs are firmly on the floor. On my floor even as little as 1" out of position is a problem. I marked the floor so I can reposition it exactly.

It really is a great lathe.

Re: 3520b resonance

#3

Re: 3520b resonance

John Lucas

I found that adjusting all 4 legs so the machine is level in all planes helps. I think it's because an equal amount of weight is on each leg. I also try to keep the adjusters as short as possible.

I have 300lbs of gravel on my lathe and it still vibrates with out of balance bowls especially at higher rpm's.

Just a thought (because I've done it) be sure and check the headstock lock. It will vibrate much more easily if you forget to lock this down.

Re: 3520b resonance

#4

Richard Allen

Re: 3520b resonance

Richard Allen

The pair of feet (headstock, tailstock) should have equal pressure. This is hard to determine.

Adjust one of the feet up and down to see if your adjustment can reduce the vibration. Try this with each of the feet. Keep changing the speed and adjusting the feet till you get the lathe running smooth.

Re: 3520b resonance

#5

Re: 3520b resonance

woodspinner-Harry Robinette

I had the same thing with my Vega 2400, I used Lyle Jamisons way of setting the feet levelers.Lyle;s way is in his I THINK last video the one he did in NC about 4 years ago.It would be to hard for me to explain it all here.The main thing is running a slightly out of balance piece (with one foot a little loose) at a slow rpm and then adjust that foot till its stopped the movement. It's something to that effect, It set my Vega perfect

I really like this, cause it was easy and fast. See if you can find one of Lyle's DVD's . Hope this helps

Re: 3520b resonance

#6

Maybe a rocking headstock

Jerry Hall

All good suggestions previously. I would add to what John Lucas touched upon: make sure your headstock is well locked down. If it is and you can see a widening and shrinking gap when you try to rock the head stock then you may have dirt in the ways, or worst case a poorly machined non flat interface at the ways. See "Head Stock Rocking" toward bottom of page here:

https://docs.google.com/View?docID=d4b7vjd_15djv9mx&revision=_latest

I turned a handle similar to a long gouge handle and put it on the headstock lock lever. That made it much easier to cinch it down. But if that doesn't do it and you can see evidence of a high spot on the headstock, and you can get a feeler gauge under one side of the headstock then I would hit up Powermatic for a possible warrantee replacement. I was out of warrantee when it happened to me but was able to lap my headstock flat. No problems since. Great lathe.

Jerry

Re: 3520b resonance

#7

Re: Maybe a rocking headstock

Rob Kennedy

Well thank you folks for all the ideas i was sure worried for a while there but had a look at Lyle J's DVD and sure enough his system works a treat! No more noise and everything running like a dream