Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Apprentice Crown Revolving Center

Posts

Apprentice Crown Revolving Center

#1

Apprentice Crown Revolving Center

Ed Moore in SW VA

The title of this post should be "Mutter, mutter, cuss, cuss!" I purchased the aforementioned revolving center and it arrived today. I noticed a set screw on the side and because I thought that the center was fixed unlike the Steb centers, I loosened it. WRONG! Suddenly the center released and fired across the shop, hitting a steel cabinet. To my amazement, I found the little center on the lower lip of the steel door. To my dismay, there is no sign of the little internal spring. It may have also hit the steel cabinet, but it could have rebounded unpredictably. I must either find or replace that spring.

Warning! Be VERY careful if you loosen the set screw. I would suggest holding the revolving center vertically with the point against the bench and under downward pressure if you choose to do this. Then raise the center carefully.

Ed

Re: Apprentice Crown Revolving Center

#2

Mike Stafford

You'll put your eye out!  Be careful!!!

Mike Stafford

Re: Apprentice Crown Revolving Center

#3

As usual, some smart guy started.......

JamieDonaldson

... taking things apart without benefit of reading the instructions! :D

Re: Apprentice Crown Revolving Center

#4

Re: Apprentice Crown Revolving Center

Peter Toch

How many times do I have tell you not to play with big boy toys! You have a better chance of finding the proverbial "needle in a hay stack" than finding the spring that launched itself with your able bodied assistance.

Email me the approximate diameter of the hole where the spring use to live and I'll bring my collection of spare springs with me to the Thurs. meeting for the demo by "what's-his-name." I'm sure we can save your butt. Bring the revolving center, point, and set screw with you. BTW, do you really think you are the only one that does dumb things? I have spare springs for a reason, to save others...right.

Peter Toch

Re: Apprentice Crown Revolving Center

#5

Thank you Peter.  I will do as ...

Ed Moore in SW VA

requested. The spring must be 1/4" or smaller and maybe an inch long. I'll measure tomorrow.

And I will do a thorough search. Fortunately this area of the shop is not where the shavings fly.

In retrospect, I am darn lucky it didn't hit my eyes. The force would have been sufficient to do damage.

Ed

Re: Apprentice Crown Revolving Center

#6

Re: Thank you Peter.  I will do as ...

Carol Reed, Strawberry, AZ

Time to go trolling with a magnet on a stick. DAMHIKT!

Re: Apprentice Crown Revolving Center

#7

Mike Stafford

If it landed in the tool bins....

Mike Stafford

there is no chance it will ever be found. :b :D

Re: Apprentice Crown Revolving Center

#8

Steven Antonucci

World's smallest jar of snakes 

steven antonucci

Re: Apprentice Crown Revolving Center

#9

Re: Thank you Peter.  I will do as ...

Ed Moore in SW VA

Carol,

I am about to head for the shop and my focus is on finding that spring. I have considered the magnet-on-a-stick approach. Are you saying that it works?

There are no shavings in this area. But MANY small pieces of exotic wood are piled there.

Ed

Re: Apprentice Crown Revolving Center

#10

Carol, no luck, still muttering.   

Ed Moore in SW VA

Re: Apprentice Crown Revolving Center

#11

Re: Thank you Peter.  I will do as ...

Carol Reed, Strawberry, AZ

A larger bar type magnet, like for nails, is not efficient for nooks and crannies. The magnet is not strong enough, much beyond 1/2"-3/4" away.

One trick that has worked for me was stacking small rare earth magnets on the end of a longer 1/4" rod and poking the other end into nooks and crannies. It needs to be real quiet so you can hear the 'snick' of the rod attracting something.

Good luck. It does help to have a general idea of where to look. BTDT way too many times!

Good luck on your PET scan. We're still praying, you know.