Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

craftsmen annoys me...

Posts

craftsmen annoys me...

#1

craftsmen annoys me...

avalon

My local sears has a nice tool selection, but the people there have no idea how to use a hammer... cant even ask simple questions..

and craftsmen.com is useless...

even the manuals will tell you what a part is, but now what it's for and how to use it..

so a friend sold me a 12 inch craftsmen band saw.. and i've never been able to get it to cut well... lots of burn marks on the wood, etc...

and i dont know what the little wheels are for ( i would assume to keep the blade from wobbling) but i have no idea if they're supposed to always touch the blade, lightly touch, not touch but almost touch, etc..

or i wonder if i have a dull blade...

Re: craftsmen annoys me...

#2

JL

Re: craftsmen annoys me...

JL

The Bandsaw Handbook by Mark Duginske.

Good book to have.

Where to start. Get a copy of your manual. If you don't have one, try to find it on-line.

The little "wheels" might be your bearing guides. The side bearing guides should be "almost" touching the blade. I usually set mine to a paper width from the blade. The side bearing guides should be about 1/16" or so in back of the teeth. I set my rear bearing guides to just in back of the blade.

This is assuming your blade is reasonably tensioned.

Anyway. How I proceed is usually as follows.

Unplug the bandsaw.

Put on the blade. Guides are usually in a raised position.

Tension the blade - I usually strum the back part of the blade where it goes from wheel to wheel (on the side away from the guide) and use that as an audible cue as to when it is properly tensioned. You could also check to see if you get just a 1/4" deflection by pressing on the side of the blade.

Track the blade. I usually rotate the top wheel by hand and adjust the tracking so that the blade is in the middle of the wheels.

Adjust the guides.

Spin the wheels again.

Check the tension.

Lower the guides.

Whatever you do - read the manual first.

Re: craftsmen annoys me...

#3

Re: craftsmen annoys me...

don lewonczyk

Sears sell How to Books on all their tools, including set up, how to use, etc. You have blade guides above and below the table that have to be aligined, the guide bearings should have a playing card thickness between blade and guides. The guides should support the blade right behind the teeth during the cut. You don't have to force the blade to cut, just glide the wood with your fingers and hands out of the way, the height setting of the blade guard should be supported 1/4" above the work piece. Get a book and read it or go online and look up bandsaws. Sounds like you have a few things going on, dull blade or not the right blade for the job, guides not lined up top and bottom,blade wheels not parallel with each other. My advice get a good book on band saws, read and understand all the safety issuses then proceed with adjustments etc. I havn't covered much but I hope it helps. DonL

Re: craftsmen annoys me...

#4

Re: craftsmen annoys me...

john lucas

What they said and on the small saws like this blade tension and tracking are important. The blade should track near the middle of the large drive wheels. There should be an adjustment that tilts one of the wheels (usually the top). This adjustment will move the blade on the wheel. With the saw unplugged you can rotate the wheels by hand and check the blade tracking.

Blade tension adjustment is often finicky on these saws. I don't know the best way to tell you to set this. Too tight and it will affect where the blade tracks on the wheels and may come off. Too loose and it won't cut a straight line because the blade flexes. With the upper blade guide retracted to full height the blade should have just a little flex when you push on the center. I would hazard a guess of 1/8" with moderate pressure. Those are thin blades.

The very first thing I would do is buy a new blade. That and the bearing adjustments may solve all of your problems from the start.

Re: craftsmen annoys me...

#5

Walt Bennett

Re: craftsmen annoys me...

Walt Bennett

My experience with almost all places that sell tools is that the individual walking the aisles or behind the register is only a sales person. Sales people these days are only trained on where things are supposed to be and how to get money from people. Not even specialty hobby stores have sales people that know how to use everything in the place - or sometimes even ANYthing in the place other than the register. Sears puts its tool knowledge into books (they make more money that way) and limited customer support. Specialty stores have knowledgeable staff folks you can email or sometimes talk to on the phone, also sell books and usually sell hands-on courses as well. None of them could turn a profit if they just had staff that really knew everything about all they sold - if they did, prices would be at least 10 to 20% higher. This is all the same thing as how we all want cheap food, but don't want illegal immigrants. Can't have one without the other.

Re: craftsmen annoys me...

#6

Re: craftsmen annoys me...

D. Hansen

Iturra Design in Jacksonville Florida has an excellent tutorial on band saw tuning and caring for. Their phone used to be 888-722-7078. They also carry generic parts for many different saws. They are easy to speak with and free with their advice.

Re: craftsmen annoys me...

#7

Crafstman Quality

bill Crommett

A number of years ago I sat next a man at a Rotary meeting who said he was visiting with his wife's folks on the way to Spain for the winter. He told me that he had retired from Sears several years ago and that his position was in sales in the tools department. I told him that if that was several years ago he must remember that Craftsman was at one time a sign of Quality. He gave me a funny look and said that the penny pinchers have really ruined a good thing, and he was glad to be gone from Sears.

Sears hand tools re still pretty good, but I will never again buy any of their power tools.

Re: craftsmen annoys me...

#8

Re: Crafstman Quality

Carole Valentine

"penny pinchers have ruined a good thing"

Isn't that the truth! Everybody wants cheap in price and the result is cheap, shoddy merchandise. I would much rather pay more for quality crafstmanship that's going to make me happy than to save a few bucks and think "what a piece of crap!" every time I use the product.

Re: craftsmen annoys me...

#9

Re: Crafstman Quality

John Lucas

Bill I hear ya loud and clear. I have several older Craftsman power tools that I'm still using and they are 30+ years old. Since then I've gone through several of their newer tools that only last 3 years or so. The final straw was when I took a $29 power drill in to buy a new switch for it. They told me they didn't carry parts for tools under $30.

If you've followed the posts on people trying to get repairs and parts for their new 15" lathe you know why I would not buy a power tool from them.

Re: craftsmen annoys me...

#10

STAND BACK!

mjonesrdg

PLEASE STAND AWAY FROM THAT MACHINE!

All bandsaws, (including craftmens) come with a simple requirement. GET WELL ACQUAINTED WITH ME BEFORE YOU START TO FIDDLE AROUND WITH ME...and she'll nip the end of your pinky right off if you fail to heed that requirement.

Avalon! your post, to me, is a RED FLAG warning that you are not getting well enough acquainted with how to handle your new shop baby. I'd suggest you make your next stop Barnes and Noble (or similar) and pick up a copy of "The Band Saw Book" and spend a little time with that.

Your loving and educated touch will result in the responses you so earnestly long for from her and will go a long way toward a lasting and satisfying relationship.

Picture yourself with her tension adjusted, her thrust bearing in place, and her drift smartly accounted for. And Always, all ways...

respect your bandsaw!

Re: craftsmen annoys me...

#11

Re: GOOD ADVICE

Steve Criscenzo

I was preparing to write a similar message. It appears clear that the users does not understand the way the machine works and that usually results in trouble or at least a good scare. This is even more likely with a lower price (quality) tool.

Avalon, keep it unplugged until you understand how it works. Find a friend to show you or get a book. Bandsaws can be deceptively dangerous.

Re: craftsmen annoys me...

#12

Keith Tompkins

Re: STAND BACK!

keith tompkins

Thanks for posting this! Avalon, you seriously need to buy a book on the bandsaw, then learn to set up and operate the saw from an experienced saw operator. That little bandsaw may burn through wood, but it will take your hand off before you know what happened. All stationary power tools, including your lathe, can be very dangeous!

Re: craftsmen annoys me...

#13

Re: craftsmen annoys me...

Ace Foster

One additional point: when you put the new blade on, be sure the teeth point down towards the table where the blade goes thru the table. DAMHIKT,

Ace

Re: craftsmen annoys me...

#14

Steven Antonucci

Good post!

steven antonucci

I agree that if you don't know what all of the moving parts are there for, then you probably shouldn't be using it. Especially, if you are posting this on a woodturning forum, where the logs are still round. Odds are that you are going to break a bunch of blades and maybe shed some blood if you don't read up.

Steve

Re: craftsmen annoys me...

#15

Re: Good post!

D. Hansen

Avalon, As mentioned you are probably from the world where things are somewhat round. Never Never never try to cut a log with the round side down. The bald will grab and pull the log holf or full round out of your hands in a twinkling. You'll lose a finger without even knowing it. . ti,l, it is too late. Get some instruction and experience the former rapidly the later slowly.

Re: craftsmen annoys me...

#16

Re: Good post!

avalon

If you actually get the craftsmen manual for the band saw, it only tells you what the parts are and how to order more if they break..

It does NOT tell you what they are for, how to use them, how to adjust them, how to.. etc..

so it's frustrating.

And i'm in a town that has a barns n ignoble, but their woodworking section has books like...

The Hammer and it's use in medieval housebuilding...

so pretty useless... I was hoping someone would point me to a good website... I'm pretty computer illiterate ... it took me 6 months just to find this place..

went to lowes today to see if they could recommend a new blade and see if their bandsaws had similar knobs.. the head tool guy had no idea what a bandsaw was for or why you would need one.

so help me woodcentral.. you are my only hope.. (starwars..)

Re: craftsmen annoys me...

#17

Re: Good post! Try here and here

mjonesrdg

http://www.amazon.com/Bandsaw-Book-Lonnie-Bird/dp/1561582891

http://www.amazon.com/Bandsaw-Book-Lonnie-Bird/dp/1561582891 (paperback 13.95)

Re: craftsmen annoys me...

#18

Steven Antonucci

The book has the parts diagram because you'll need

steven antonucci

to order parts when they break, not if...

I gave mine away to a guy who had nothing, and when I did, he still had nothing and now it needed a bearing...

Get some help on Youtube and some of the other woodworking forums. If you see a hand moving towards the blade, stop the video and find another one...

S

Re: craftsmen annoys me...

#19

Re: The book has the parts diagram because you'll

Barry L Elder

I recently purchased an (antique) CRAFTSMAN Band saw/Sander that was made about 1979 and it works very well except for a motor that just hums. Took off the starter capacitor and had it checked and it is OK. The guy at the armature shop said he thinks there is a switch inside that is caked with wood dust and is not making good contact. If I spin the shaft it works just fine. My point being, at one time CRAFTSMAN made some excellent tools! And I had no trouble downloading the Operators Manual from the net. Too bad some of our younger entrepreneurs don't buy the CRAFTSMAN name and build tools to match.

Re: craftsmen annoys me...

#20

Re: craftsmen annoys me...

Bart Leetch

http://www.youtube.com/results?search_query=adjusting+your+band-saw&aq=f