Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Shavings

Posts

Shavings

#1

Shavings

John Jordan

There's a point in a hollow turning when most of the bulk is out, and there is room for a lot of shavings before needing to stop and clear it out.

This is walnut 10-11 inches, the shavings are from the little 3/16 tips I use in my tools. (handheld :) )

John

Re: Shavings

#2

Re: Shavings

Jennifer Indy.USA

Looks like you had a good day :)

Re: Shavings

#3

Alan Zenreich

Re: Shavings

Alan Zenreich

Looks like something from a sci-fi movie...

Re: Shavings

#4

I'm assuming the compressor nozzle

john lucas

on the lower left wouldn't work anymore.

Re: Shavings

#5

Re: Shavings

Jorge Casta�eda

If you wait too long blowing air does not work, in the other hand I can relate to not stopping and have one continuous cut.

Nice work!

Re: Shavings

#6

Beautiful.

Greg Haugen

Gotta love walnut. It's one of my favorites.

Love the picture. :-)

Re: Shavings

#7

Steven Antonucci

You could laser them out 

steven antonucci

Re: Shavings

#8

Steve Kubien

This raises a question...

Steve Kubien

The only time I get shavings like this while hollowing is if I use a Hunter cuttter in my Jamieson rig, never with a handheld tools or HHS tips in in my rig. What gives? Is it a matter of cutter height or is your skill vs my lack thereof?

Thanks!

Re: Shavings

#9

Re: This raises a question...

Greg Haugen

Steve,

How's your wood oriented, end grain or face grain?

Re: Shavings

#10

Steven Antonucci

Better question:  Are you cutting it "right"?

steven antonucci

Only going to get curlies by cutting with the grain and downhill... if you are cutting into end grain, you get fuzz...

S

Re: Shavings

#11

times have certainly changed

Michael Mocho

Hey John,

Do you remember when ��

The long curls were on your head

and the dust came out of your turnings?

Now the dust is on your head, and the long curls �.

Re: Shavings

#12

Re: times have certainly changed

John Jordan

That's good Michael. :) The tips have a fresh burr. The piece is oriented side grain, but the cut direction is not too important inside a piece like this, and I don't worry about it much. This is pretty typical and basically what you should get with decent wood.

John, the air is for after I have used the wire hook to get the bulk out. I blow out every spec so I can get a good clean finish cut without the shavings interfering.

I did not mean to imply I don't stop to clean the shavings out-you should never fight against the shavings.

John

Re: Shavings

#13

Steve just gave the answer I was going to give.

John Lucas

Re: Shavings

#14

Steve Kubien

Re: Better question:  Are you cutting it "right"?

Steve Kubien

Well duh! Most of the forms I have done are endgrain. Ya know, I cannot even remember the last time I did one. It's got to be 8 months or more....

Thanks

Re: Shavings

#15

Steven Antonucci

If you hollow with a hook, you get shavings

steven antonucci

And it removes a lot of material very, very quickly.

I'll be making hook tools in the forge tomorrow for about a dozen NJ Woodturners members...

S

Re: Shavings

#16

Leo Cuellar

Re: If you hollow with a hook, you get shavings

Leo Cuellar

Hey, Steve, would you be willing to post a picture of a finished one? I'd like to see what your design looks like. Almost dry enough out here to fire up my forge.