Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Just a bit of counter balance

Posts

Just a bit of counter balance

#1

Just a bit of counter balance 

Terry Scott

Just a bit of counter balance needed to turn this piece I call the traffic light

I had an email asking if I could post this again

I love a challenge

My wife went crook as she had to go tow the horse float and wondered where her tow ball had gone.

This piece was made from a plank of Macrocarpa for an exhibition that required the piece to be made from this wood.This work resides in a Home in Southern China

glad someone liked it.At least I had enough room on the package for all the stamps needed

Why did I do this because I could l.o.l

Re: Just a bit of counter balance

#2

You are a crazy man.

Toney Robertson

Even just looking at that sends shivers up my back.

Re: Just a bit of counter balance

#3

Steven Antonucci

Open the shop door and you don't need to sweep

steven antonucci

but you might had to bolt the lathe down to keep it from taking off...

S

Re: Just a bit of counter balance

#4

Re: Just a bit of counter balance

Bob Macgregor

I'm with Toney.

Looking at those pictures made me think of the airplane/fight scene in Raiders of the Lost Ark.

BOB

Re: Just a bit of counter balance

#5

Don Leydens

Re: You are a crazy man.

Don Leydens

Terry, I think you just like to turn alone. You should have your shop sectioned off with bright yellow tape! The bomb squad might volunteer to do it.

Re: Just a bit of counter balance

#6

What did it sound like?

Adrien

Re: Just a bit of counter balance

#7

Leo Cuellar

You need to dig a pit...

Leo Cuellar

and make a nice long & deep concrete box cross way at the end of your lathe. Cover it with some heavy steel grating & when you need more swing, you can just remove a piece. :D Would make a convenient place to stow the shavings for a while if you're workin' on a lot of smaller stuff.

Re: Just a bit of counter balance

#8

What rpm did you turn that at----

Galen Vetterick

Guess if it hit you the faster the better so you do not suffer for long!

Would scare the ----- out of me!

Re: Just a bit of counter balance

#9

Not for wimps!!

Jorge Casta�eda

Terry,

You are very ingenious and have a clear vision of what it takes, and just do it. Thanks for all your posts, we may little by little grow to it.

Cheers!

Re: Just a bit of counter balance

#10

What's the lifespan of your bearings?

Craig Daymon

Terry,

Great job, as usual, but I'm curious just how often you have to replace bearings in your headstock. I would think that level of eccentricity (with respect to the turning, I'll leave the question of the turner to another post) you would be burning out bearings weekly.

-Craig

Re: Just a bit of counter balance

#11

Terry -- you make me smile.   

GaryG in MD

Re: Just a bit of counter balance

#12

Re: You need to dig a pit...

Terry Scott

This will turn 1800 no sweat ,I dont ned to dig a hole just lifting the lathe 4 inches Ill swing 8 foot what did it sound like well Chop chop chop at this diameter the lathe tends to cycle so the speed isn't constant on the downward swing it speeds up a bit adding to the noise

Not hard on the bearings at all as i spend allot of time balancing .The piece

will rotate anywhere around the 360 and stay put

Re: Just a bit of counter balance

#13

A little too scary for me, but cool

Mike Foster

Re: Just a bit of counter balance

#14

Re: Just a bit of counter balance

Philip Duffy

So, Terry, what brand of body armor were you wearing when turning this monster? Phil

Re: Just a bit of counter balance

#15

Re: What rpm did you turn that at----

Terry Scott

You have to turn fast enough so you get a half decent cut

Its at the perimeter were the sped is greatest so 800rpm is motoring on the out side

Re: Just a bit of counter balance

#16

Single-bladed windmill  *LINK*

Bob Macgregor

As long as it is balanced, there shouldn't be a problem with the bearings.

I think I've go this figured out: I bet this is a disguised test-bed for different configurations of single-bladed windmills.

This NZ design has two counterweights:

BOB


http://idealog.co.nz/magazine/22/one-blade-wonder

Re: Just a bit of counter balance

#17

Terry...

Barbara Gill

Could you please translate for this Southerner?

"My wife went crook as she had to go tow the horse float..."

Re: Just a bit of counter balance

#18

Re: Terry...

Don at Central Illinois

I 'think' he meant, she went a little crazy because she had to use the horse trailer and couldn't find the ball hitch. Let's see how close I got when Terry answers.

Re: Just a bit of counter balance

#19

Re: Terry...

Barbara Gill

Ahhhhh

Re: Just a bit of counter balance

#20

Re: Terry...Crook

Terry Scott

Crook gave me an Ear full