Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

No end to how I can screw up

Posts

No end to how I can screw up

#1

No end to how I can screw up

Stuart Johnson

I was turning a pretty little vase from some Ambrosia Maple my trading buddy Steve sent me. For a change I was concentrating on trying to do each step rather than banging into it, letting chips fly and hoping for the best. The outside was turned in one of the most pleasing shapes I've made and sanded to 400. The center drilled and using my Monster rig with laser the top third turned to about 1/8". Well the very top was thicker, I haven't gotten the top corner part down yet. At this point I should have changed to the semi curved tool but as best I can tell started to use the side of the tip. This left a nice laser dot that was not elongated as I proceeded to cut to a -1/64 wall thickness.

New step to add to the check list: Double check the laser dot and what part of the tool cutting tip is in use.

Re: No end to how I can screw up

#2

Re: No end to how I can screw up

Jeff Willaford

Stuart, is that what they call negative space?

Re: No end to how I can screw up

#3

Re: No end to how I can screw up

charlie belden

It's impossible to Idiot Proof anything, a I have repeatedly proven and as you've discovered.

Since the Monster cutters are made from square stock, the corners are sharp and can cut AND CATCH. Having done what you did, I've seriously considered "easing" the "left" upper corner of the cutter to Idiot Proof it. Alas, in addition to my charter membership in the Idiots Club, I'm also a certified Master Procrastinator.

I've been thinking about a way to vary the diameter of a laser's "dot". Rather than offset the dot from an area of the cutter, have the dot the full radius of the cutting parts. It wouldn't be as small a dot, but you wouldn't have to remember exactly where you've offset it from.

Re: No end to how I can screw up

#4

Let's not make it a competition!!!

Richard Jones

I'd win for sure...............

Hard lessons are, well, hard...............

R

Re: No end to how I can screw up

#5

YOU'RE ALL LOOSERS!!!!

Dick Wilson

I am so far ahead of all of you on hollowing system screw ups that you need a GPS to find me :D :D :D

For me it wasn't so much the neck or shoulder that did me in. It was the transition from the side to the bottom. I was either too thick and I thought it was just right OR OR I thought I was spot on with the laser for the wall thickness and pow!!! I have turned some of the prettiest funnels you have ever seen. They are now part of my "Burn Barrel Ressurection" series. :) :)

Stuart, Here is what I have done and do. It is not full proof but it sure helps. I placed a triangular arrow painted red on the top of my laser assembly. I always point it where the cutter is. Gives me "vision" if you will. I have trained myself to check the wall thickness on my cutter. I made a bunch of little blocks at 1/16" increments for setting the laser. Think of an upside down "T". I also had a laser set up with round bars. I scraped those. A bump on the laser light and you are screwed. I made a new laser light attachment out of square tubing.

Re: No end to how I can screw up

#6

Steven Antonucci

I will dig through the pile to see if I have more

steven antonucci

I just split the last whole log section for firewood this past weekend! I have some maple in the rough, but I'm not sure if it's that ambrosia that I sent you or otherwise.

Assuming of course that I am the Steve you meant...

S

Re: No end to how I can screw up

#7

Re: I will dig through the pile to see if I have m

Stuart Johnson

Steve, you are. Thanks for the offer but I'm pretty well set right now. It's just that it was such a pretty piece of wood and for a change I had done justice at least to the outside.

Isn't it something when you think in this part of the country Mesquite is used for firewood and Maple is purchased.

Re: No end to how I can screw up

#8

Steven Antonucci

Perspective

steven antonucci

I was in Hawaii a while back and they were splitting Koa for firewood.

I am good friends with the guy who owned the tree. I took more than I could ever turn, and left more than either of us could burn in 5 winters. I'll see him this weekend, so if there is anything still there, it's not a big deal. I still have more wood than I can turn...

S

Re: No end to how I can screw up

#9

Re: No end to how I can screw up

Bob Macgregor

Its all part of the learning process.

If it is too frustrating, you could just turn the outside to the "perfect" shape, drill a hole for the neck, then put in on the shelf; if nobody picks it up, they'll never know its just a fancy block of polished wood rather than a "real" hollow form with 1/32 in. walls!

BOB