Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

chain saw sharpening problem *LINK*

Posts

chain saw sharpening problem *LINK*

#1

chain saw sharpening problem *LINK*

john lucas

I have been using the Husquavarna sharpening guide for years with great success. I used my saw a lot this last week and purchased a new sharpening guide because my old one was worn out. I sharpened the blade and now the saw cuts to the left. It has always cut a perfectly straight line using this tool to sharpen. Anyone have a guess as to why and what would I do about it.


http://loggingsafety.com/content/combi-gauge-chain-saw-sharpener

Re: chain saw sharpening problem *LINK*

#2

Re: chain saw sharpening problem

Michael Mocho

Hi John,

Before you assume it is the chain or your sharpening methods, you may want to check to see if the edge of the bar is still square- over time they tend to become angled, and the chain takes on a subtle tilt that leads towards one side. I have been able to correct a curved cut by filing or grinding the edge back to square.

Good luck!

Re: chain saw sharpening problem *LINK*

#3

Re: chain saw sharpening problem

john lucas

It just dawned on me that I pinched the chain on a limb that sprang in the wrong direction and it pulled the chain off the bar. There were some burr's on the part of the blade that runs in the bar. I ground these off and the chain ran smooth in the bar. This could be the problem but I didn't grind off anything more than it took to get the metal flush. Do you think the bar is damaged?

Re: chain saw sharpening problem *LINK*

#4

Re: chain saw sharpening problem

john lucas

Thanks Mike. You answered just as I remembered what had happened. I'll try grinding the bar and I may have another chain. I'll try that one on the bar. That should tell me something.

Re: chain saw sharpening problem *LINK*

#5

Re: chain saw sharpening problem

woodspinner-Harry Robinette

John

The only thing I can think of is you cut to hard on the right teeth. I know your use to sharpening your saw but I know it can happen it has to me.

Re: chain saw sharpening problem *LINK*

#6

Re: chain saw sharpening problem

Michael Mocho

I would try another chain on the saw if you have one- that should answer the question rather easily.

Re: chain saw sharpening problem *LINK*

#7

Re: chain saw sharpening problem

robo hippy

I do flip the bar over each time I change a chain. That may help as well.

robo hippy

Re: chain saw sharpening problem *LINK*

#8

Re: chain saw sharpening problem

Galen Vetterick

You may have put a slight bend in the chain links so a different chain will answer that. You can lay the suspect chain on a flat surface and see if it lays flat. A small twist can make it run off. You may have spread the groove in the bar when you pinch it. Like has been said make sure the edge is flat and you can look at it and peen the groove closed ever so lightly if it has been worn too much or bent out.

Where you forcing the cut. Excess pressure on the chain and bar can make it track off if the grooves in too wide or the chain is a little too loose.

I assume all the depth gauges/rakers are filed to the same so the cut is the same per tooth.

Re: chain saw sharpening problem *LINK*

#9

Dale Jablonski

Re: chain saw sharpening problem

Dale Jablonski

You are remembering to check and file your rakers when your sharpen your cutting teeth right? If you pinched your bar then that can also cause your symptoms.

Re: chain saw sharpening problem *LINK*

#10

Re: chain saw sharpening problem

Keith Newton----Little Rock, Arkansas

I always try to wear a magnifying visor when I sharpen, or at least inspect all teeth after I'm done. If the left side is sharp and the right side still has some dullness, it will cut left, toward the path of least resistance.

Re: chain saw sharpening problem *LINK*

#11

Re: chain saw sharpening problem

John Lucas

I'm gathering all this info. Won't have time to get in the shop until Thursday and that assumes my boss is doing the evening shoot. If not it will Sunday since we have graduation this weekend.

Re: chain saw sharpening problem *LINK*

#12

Re: chain saw sharpening problem

bill Crommett

John: I always had that problem when I sharpened my chains myself, but when i took the chains to the Stihl dealer I got a perfect job. I don't know what I will do now that the Stihl dealer has gone out of business and the new dealer is inexperienced as well as higher priced. It helps, though that I sold the big saw and now I don't do much with the new one with an easy starting system.

Re: chain saw sharpening problem *LINK*

#13

Chain Balance

Mark Mandell - Gone Round In Jersey

John,

Take a mic to the teeth on both sides. I anticipate that one set (or several cutters) is longer than the other side. This will cause the chain to pull to that side because that cutter(s) is/are cutting a bit more deeply. I use a Tecomec grinder, and I start by checking each tooth on the chain for length. I then set the grinder to the shortest tooth. That way the chain's bite is precisely balanced left-to-right and the runs runs straight.

As to pinching your bar, put a straight-edge to it and check. If the bar is bent, trash it and start fresh. There are shops who can straighten a bar, but for most anything under 28" it's not worth the cost.

Re: chain saw sharpening problem *LINK*

#14

Re: chain saw sharpening problem

John Lucas

Bill The reason I started sharpening my self is I took it to my local Stihl/Husquavarna dealer to be sharpened and the guy stuck it in a vice and used a round file with not guide whatsoever. I knew I could do better. My friend Brad Sells who makes a living with a chainsaw had a guy working for him who is a long time logger. They both recomended the Husquavarna sharpening guide as the way to go.

The only problem I have with it is the files don't seem to cut very long. I feel like I'm constantly buying new files.

Re: chain saw sharpening problem *LINK*

#15

Re: Chain Balance

John Lucas

Mark This brings me to another question. Many people have recommended using the Dremel with it's tools. I am happy with my Husky guide but I seem to wear out the files really fast. I've thought about the Dremel but was concerned that I would take off more metal on some teeth than others. With the file I always use the same number of strokes on each tooth and it's worked well for many years. If you use the Dremel how do you insure you are taking off the same amount short of measuring each tooth, which would take too long.

Re: chain saw sharpening problem *LINK*

#16

Re: Chain Balance

Mark Mandell - Gone Round In Jersey

Hi John,

I used to file, the I fussed with a Harbor Freight grinder, then a friend's Dremel, until I finally went out and bought a real chain grinder. I bought a Tecomec which is very precise and will grind any chain that I'll ever have use for. I set my chains up with my personal grind angles and I take them off the saw when they barely start to drag. That way all I need do is "kiss" them with the grinder and they're right back to sharp. My friends all bring their chains over to me and they brag about how much smoother and faster they cut. The first job with their chains is to mic all the cutters to find the short one (after the lawnmower shop does them once they're way off), and then set the stops to that measurement. The cutters all come out within the tolerance of my digital mic which runs to 4 decimal places. Grinding the depth stops is equally easy. I get more than 15 sharpenings out of a chain before I pitch it, because I'm taking so little off the cutters each time. Takes me 5 min. to do each side of a 28" chain plus another 10 if I have to grind the depth stops.

The Dremels and files are fine for use in the field, but when I go out cutting, I'll take 3 chains for each saw so I don't need to fuss with sharpening anyway.

Re: chain saw sharpening problem *LINK*

#17

Re: chain saw sharpening problem

bill Crommett

I guess I was just lucky to find a guy who knew what he was doing.

Re: chain saw sharpening problem *LINK*

#18

Re: Chain Balance

Barry Irby

John, I am not as well equipped as Mark. I use the Dremel. I sharpen each chain three or four times and then take it to a local Stihl dealer if it starts to bother me. The Dealer is hit or miss. If the right guy is there they do a really good job, but if not they just set the grinder up and let it "eat". I never see them look for the shortest tooth. I think they just take off enough to be sure they are all the same. The chains do cut better, but I feel like it costs me a lot of metal. I have tried to figure out some more sophisticated guide for the dremel, but have not come up with anything. I use a light touch and take off almost nothing.

Re: chain saw sharpening problem *LINK*

#19

Re: Chain Grinder

Mark Mandell - Gone Round In Jersey

Hi Barry,

I'm not well equipped in this area. The Tecomec is really an "entry level" grinder for round chain. It won't do square chisel chain. I've had mine for about 5 years and they've gone up in price in that time, but it's not even close to a Silvey which is the gold standard for chain grinders at 3 to 4 times the price. But my unit has paid for itself several times over in chain life and sharpening savings, and when I figure in what I've saved my friends, it's been downright cheap.

m

Re: chain saw sharpening problem *LINK*

#20

Re: Chain Grinder

john lucas

I didn't have another chain so I simply flipped the bar over and resharpened the chain and now it's cutting straight. I could not see anything wrong with the bar other than it wasn't perfectly flat. It had a very slight bow so I straightened it. The groove and edges of the bar looked very clean and the chain was flat.

Re: chain saw sharpening problem *LINK*

#21

Re: Straight Bar

Mark Mandell - Gone Round In Jersey

John,

Watch your bar for straight. From what I was told, once they're bent it changes the set in the metal and as the bar heats up during use it will tend to "rebend" itself. If yours was off by a 1/4" or so, it may not be a big deal, but keep checking it. A bent bar is more likely to throw a chain during cutting.

A new bar ain't that expensive.

Re: chain saw sharpening problem *LINK*

#22

Re: Straight Bar

john lucas

Mark Mine was only off by .020, .030" or so. I wouldn't be surprised if any bar would be off that much after a years use just from the everyday abuse. I was just trying to find a problem.

Re: chain saw sharpening problem *LINK*

#23

Picky Picky Picky

Mark Mandell - Gone Round In Jersey

I've seen brand new (blister-pak) bars off by .02. I thought you meant "BENT" :D