Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

DustRight DC fittings

Posts

DustRight DC fittings

#1

DustRight DC fittings

Carole Valentine

Not long ago I finally purchased a "real" dust collector and found that fittings for various machines were a nightmare - there seems to be no reasonably tight standard among manufacturers, especially when it comes to quick connect fittings which would drop off if you looked at them even slightly crosseyed. The long hose was also a pain (No, I have not gotten around to running duct work - someday - maybe...)

Anyway, in desperation, I tried the DustRight fittings from Rockler and the expandable hose. The connectors are fantastic - a rubber boot with a clamp that gives you a secure seal on any port. Swivel connectors at the DC and the opposite end of the hose prevent any twist. The hose expands from about 4' to about 28' so I can reach anything in the shop without moving the DC, yet when it's "home" at either the bandsaw or the lathe I don't have coils of hose lying around. I won't go into all the fittings available, and they are more expensive, but suffice it to say that if you don't have ducting and move your DC from tool to tool, you might want to take a look at this system. It solved multiple aggravations for me.

And no , I don't work for Rockler, just think it is a good product that solves a common problem for the small shop. ;)

Re: DustRight DC fittings

#2

Richard Allen

Re: DustRight DC fittings

Richard Allen

The dust right series is terrific. They also have a long wand for standup floor cleaning and a short "claw" for bench top cleaning.

Re: DustRight DC fittings

#3

Re: DustRight DC fittings

Carole Valentine

Yes, I have both. The floor wand is great....no more "ssssshlup" and the thing is stuck to the floor like with my shop vac. ;) Now if they would just make a crevice tool....

I did cut out part of the grate in the floor attachment. It did not like the odd clump of long curly turning shavings.

Re: DustRight DC fittings

#4

Richard Allen

Re: DustRight DC fittings

Richard Allen

We make round things.

Make a 4" to shop vac reducer so you can use your shop vac accessories with your dust right.

Something as simple as a board turned round with a flange to fit on the end of the dust right with a hole in the middle for the hose from your shop vac to fit.

Re: DustRight DC fittings

#5

Katherine Kowalski

Re: DustRight DC fittings

Katherine Kowalski

One thing to watch out for...

I've had the DustRight setup connected to my dust collector for about two years now, and I generally like it. The expandable hose is great -- I use the universal connector to connect to my bandsaw, OR, alternately my lathe grouping. The only problem I've recently come across -- the universal connector/handle has now become totally stuck on one of the swivel things that I have connected to my lathe group hose. Can't seem to disengage.

Soooo... solved the problem by simply taking off the swivel off the bandsaw, and connecting it with the "extra" piece in between.

A bit of a pain, but... still works better than nothing!

Katherine

Re: DustRight DC fittings

#6

Re: DustRight DC fittings

Carole Valentine

Katherine, I have had the handle connector get a pretty firm grip on the port for my lathe collection now and then. I am wondering if it might be due to some sap or resin that gets on the female connector when I don't have the hose hooked up? Wonder if you hit yours with a hairdryer for few minutes if it would release?

Re: DustRight DC fittings

#7

Re: DustRight DC fittings

Bart Leetch

"no more "ssssshlup" and the thing is stuck to the floor like with my shop vac." ;)

Just hot glue some small hardwood wedges to the bottom of your vac floor attachment. Vac's don't work by suction but by how much air they move.;) ;) ;) ;) ;) ;)

Re: DustRight DC fittings

#8

Re: DustRight DC fittings

Carole Valentine

Yep, but I kept knocking them off. Eventually I cut relief channels with a cutoff wheel. That worked.