Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Large brass couplers for processional torches?

Posts

Large brass couplers for processional torches?

#1

JL

Large brass couplers for processional torches?

JL

I've seen the cane parts from Craft Supplies (and I've even made a cane or two).

I've been asked to make some processional torches for a church (as well as the bases by the altar). The torches need to be ~46" long. I've got a Jet 1642 - so I would have to turn them in two parts. I therefore need some sort of hardware (preferably brass) to join the two parts together. I was going to make the poles about 1 1/4 to 1 1/2" in diameter.

Re: Large brass couplers for processional torches?

#2

Re: Large brass couplers for processional torches?

Mark Mandell - Gone Round In Jersey

Go to the plumbing dept. and you'll find 1-1/4 and 1-1/2" drain parts in either chrome or polished brass. I've used such to make handle ferrules and they do just fine. Cut them with a tubing cutter for a smooth edge, and use a length that's at least double the diameter. Rough the inside surface for a good grip and set them with epoxy.

m

Re: Large brass couplers for processional torches?

#3

Re: Large brass couplers for processional torches?

John Lucas

I've used a lot of different brass plumbing parts for things. They can be turned quite easily using mandrels or chucks to hold them. Another option would be just to use contrasting wood. Drill a hole in one piece and use that for your center. Then turn a tenon on the other but leave it long enough to put a ring of contrasting wood on before the final assembly. I do this for lamps and it looks great.

Re: Large brass couplers for processional torches?

#4

Re: Large brass couplers for processional torches?

bill Crommett

JL: If you would rather have the poles in a single piece find someone with a Shopsmith. I turned a banister for a large boat once with my Shopsmith by removing the tailstock and bolting it to the wall an appropriate distance. Thus I got a 52 inch banister in one piece.

Re: Large brass couplers for processional torches?

#5

Re: Large brass couplers for processional torches?

David Walser

This trick will work with JL's Jet, too. All that needs to be done is, either mount the tailstock on a table or stand (or on the wall) at the appropriate height or create a fixture to hold a live center. If you create a fixture to hold a live center, you'll need to rig some way to vary the pressure the live center exerts against the blank -- such as using some wedges. Of course, a spindle 46" long and 1.25" in diameter might require a spindle steady to turn, where a 23" spindle of the same diameter might not.

Re: Large brass couplers for processional torches?

#6

JL

I've got a steady.

JL

Re: Large brass couplers for processional torches?

#7

JL

Good idea - thanks.

JL

I can make a nice tenon joint and disguise with the coupling.

Re: Large brass couplers for processional torches?

#8

JL

The LOML said I could get a bed extension (20")

JL

So - who has the best deals? Amazon/CPO has the BE 20 for about $220.

Re: Large brass couplers for processional torches?

#9

Here's One Now

Mark Mandell - Gone Round In Jersey

One the tap handle I made for a buddy's bar

Re: Large brass couplers for processional torches?

#11

Re: Pool cue connector *LINK*

Keith Inscho

How about an adaptation of this idea for turning a pool cue?


Pool cue plan

Re: Large brass couplers for processional torches?

#12

Wonder if you could turn it

Barry Irby

with out using the tail stock? Put a long piece of stock in a chuck and hold what should be the middle in a steady. You would have to make a "tire" to put on it. Square hole in the middle and round outer surface for the steady to run on. Keep the speed fairly slow to avoid developing "whip". Turn half of it, Turn it around and turn the other half. Then move the steady to a turned part and clean up the middle. Cut off the square ends.