Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Nova Chuck

Posts

Nova Chuck

#1

Dick Hines

Nova Chuck

Dick Hines

I just got my flier form Woodcraft. They have the SuperNova2 chucks on sale again $140+ insert.

I may have chuck #5 shortly

Re: Nova Chuck

#2

Brad Vietje

S-N-2 is a Great Chuck

Brad Vietje

Re: Nova Chuck

#3

Re: Nova Chuck

Terry Scott

I have many super novas But are getting slacked off with them as the key ways that you place the tee bar into are wearing due to the round ended Allen key

Also have 4 Trition (no longer made )They are knackerd totally for the same reason and you cannot get parts .I guess you gets what you pay for.I herd a rummour this is why they stopped making them

Ive spoken to Teknatool but they say I am doing the chucks up to tight ,The Vicmarcs I have dont have this problem as the key way is much deeper .As I can afford it I will be up grading .In Nz Dollars the price is $289 so at 140 even with 25% difference in currency Cheep

ive always been loyal to Nz Made but know there in China I feel I can go elsewhere

Re: Nova Chuck

#4

Bill Blasic

Re: Nova Chuck

Bill Blasic

Terry,

The very first thing I do is throw away the ball ended key and get a flat ended one.

Bill

Re: Nova Chuck

#5

Dick Hines

Re: Nova Chuck

Dick Hines

After I replaced the pinions in my SupreANova2 I went the the square ended allen wrench also.

Never did like the rounded end one.

Re: Nova Chuck

#6

Grind the round off the key!

Jorge Casta�eda

Terry,

From experience in other tools with round key noses, when I got the Supernova 2, first thing I did was to grind away the round. My chuck still is in good shape 4 years later.

Re: Nova Chuck

#8

Re: Nova Chuck now you tell me l.o.l

Terry Scott

How can I repair the know rounded out hex Over the last couple of years Ive weeded out the super novas as the key system was hard to use

Replacing as many chucks as I have will take a while ,

Re: Nova Chuck

#9

Re: Nova Chuck

Barry

When you get a new Super Nova II, go buy yourself a standard T-handle Allen key to fit the chuck and throw the ball-end wrench that comes with the chuck away. That's what I did and I have never had problems with the chuck wearing prematurely.

Re: Nova Chuck

#10

Don't buy a new key

Carole Valentine

Just grind the ball off of the existing one. That's what I did.

Re: Nova Chuck

#11

Dick Hines

Re: Nova Chuck now you tell me l.o.l

Dick Hines

You can get the pinions form Teknatool. As I remember they were cheap. I do they are easy to install. And while you are at it you can give your chucks a good cleaning. Kind of like killing two birds with one stone.

Re: Nova Chuck

#12

Steve Kubien

Ok, I don't understand something...again

Steve Kubien

What is the problem with the ball-ended key? I have two SN2's and no apparent issues after 3-4 years. What ought I be looking for? Why should I grind the ball off the end of the key?

Re: Nova Chuck

#13

Re: Ok, I don't understand something...again

Doug Wolf

Steve,

I have 2 SN2's about 2 years old and the hex sockets have started rounding due to the hex ball having less surface in contact with the socket. When tightening the jaws, the hex ball puts too much pressure per square inch in the hex socket and slowly but surely will cut away the flats.

I finally cut the ball off my hex key before it gets any worse. Maybe I'm overtightening my jaws but I'd rather overtighten than be too loose.

Just insert your hex key into the socket, twist back and forth and see how much play you have.

Re: Nova Chuck

#14

Steve Kubien

Re: Ok, I don't understand something...again

Steve Kubien

Thanks Doug. I will do that (and possibly grind off my keys).

Re: Nova Chuck

#15

Mike Stafford

Little known fact....

Mike Stafford

The Vicmarc hex key fits in the SN2 and vice versa or the other way around in reverse.... :b

Re: Nova Chuck

#16

Re: Nova Chuck

walta

Do you use your chucks key as a lever when removing the chuck from the lathes spindle?

Walta

Re: Nova Chuck

#17

Re: Nova Chuck

Terry Scott

when I cannot find my spanner on the floor

so yes guilty

Re: Nova Chuck

#18

Re: Nova Chuck

Doug Wolf

Never used the hex key but didn't have a wrench large enough so got my arc welder and some scrap and now I have a wrench to remove the chuck.

Re: Nova Chuck

#19

Re: Nova Chuck

Wayne Kuhn


Try a metal rod tightened across the jaws. Give it a good tug or a light impact and the chuck will loosen right up.

Wayne

Re: Nova Chuck

#20

Re: Nova Chuck

Ed Wujciak

Doesn't need to be a piece of metal. Scrap wood works fine and we all have lots of that.