Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Catches With A Hunter Tool

Posts

Catches With A Hunter Tool

#1

Catches With A Hunter Tool

Stuart Johnson

For some reason I'm having a problem with catches when using a Hunter for clean up on the inside of a vessel. I have no problem with the sides but when I get near the bottom I've had catches that ripped two pieces out of the chuck. I'm sure it is something I'm either doing or not doing but is happening when I try to get the very bottom curve. I haven't tried to come across the bottom for a final cut yet.

In the past I normally used Kelton's and have not had a problem in touching the bottom and then rolling into the cut. How is this done with the Hunter or is there something different I should be doing?

Re: Catches With A Hunter Tool

#2

Re: Catches With A Hunter Tool

Greg Haugen

Stuart,

Give us some more info so the answer will be specific to your situation

What tool(s) are you using? A hunter tool, or a tool with a Hunter tip?

Is the vessel endgrain or facegrain?

Re: Catches With A Hunter Tool

#3

Re: Catches With A Hunter Tool

John Lucas

It depends on how deep and how big the hole is for the hollow vessel. You can't do a scraping cut with the current Hunter tools with the possible exception of the tilted #1 cutter and bar. You need to be on the bevel which is hard to do when reaching in very deep.

It's not to hard to turn a concave bottom if you start from the outside and turn toward the middle. It's a little more difficult to turn a flat bottom through a small opening. Tilt the cutter about 45 degrees to the right and take a small nibbling cut from just left of center toward the center. This not only gets rid of the center nub but helps you get a feel for where the bevel is. Then you can work your way out eventually making one pass from outside to middle. I guess I should tell you this is with a #3,4 or 5.

This is a challenging cut through a small opening and probably not the best use of the current Hunter tools.

If your using the #1 in the tilted bar in a captured rig (see Lyle Jamieson's rig) then you just very carefully start in the middle and cut toward the outside. With a captured rig and tilted tool it's controllable and works quite well.

Re: Catches With A Hunter Tool

#4

Re: Catches With A Hunter Tool

Ed Moore in SW VA

Stuart,

The tip must be at a 45 degree angle or more when working the side or bottom of a box. Anything less that 45 degrees is asking for a catch. Close to horizontal is guaranteeing one.

Ed

Re: Catches With A Hunter Tool

#5

Re: Catches With A Hunter Tool

Stuart Johnson

The tool is a #3 Hunter. One piece was face grain and one end grain. Both are rather small and neither had a small opening. I could easily see inside and the face grain one was a piece of Mesquite that is actually either a wide mouthed vessel or a narrow mouth vase. I was trying to see just what I was doing what I did wrong with the other one but missed the 1/1000 of second between cutting nice and knocking the piece out of the chuck.

John, I need to go back an view your videos again. If the tool laying on the rest with the cutter facing up ... U ... on center then be rotated to the right ...C... to find the bevel of the cutter or tool? Then rotated back to the left until it starts to cut? Should the cut be above, on or below center? Should I take up knitting?

Re: Catches With A Hunter Tool

#6

Re: Catches With A Hunter Tool

John Lucas

To find out if the tool you have will work put a scrap piece on the lathe. Move the Tool rest as far from the piece as the bottom of your vessel would be. Put some masking tape on your tool rest to indicate the size opening of your vessel. Now place the Hunter tool on the scrap block with the shaft between the masking tape. Now you can see if you can move the handle and tool far enough one way or another to rub the bevel.

This is a also a good way to learn to use the tool for cleaning the bottoms. You can get lots of catches on a scrap piece with no walls and not hurt yourself.

Re: Catches With A Hunter Tool

#7

Re: Catches With A Hunter Tool *LINK*

John Lucas

Take up Knitting. You get to sit with pretty women while you do it.

Which way you tilt the cutter depends on which direction you are cutting. If you go back to the first video you will easily see this. If your cutting to the left then the cutter should be tilted to the left. If your cutting toward the right then tilt it to the right.

Normally you could tilt it a lot of different angles except flat of course. However when your down deep it's harder to rub the bevel so you have to find the sweet spot which is hard to when you can't see in very well. That's why I recommend the practice piece in the post below.

If you can move the handle far enough to the left you can start the cut at the center and work your way out with the cutter tilted left. If you can't get the cutter on the bevel starting at the center you can cheat. What I do is start with the tool tilted to the right. I start with the tool shaft acting as the bevel and touching the outer wall of the vessel. This keeps it from catching and allows you to start the cut. The cutter should be rotated to the right and the cut goes from left to right toward the center. This may not work if your opening is too small and you can't stay on the bevel. You would usually start a cut like this with the tool shaft against the wall and the handle toward the right side of the vessel opening. You may end up with a concave bottom unless the opening is large enough to move the handle to the left.

I've put a link to the Hunter video for you.


http://www.hunterwoodturningtool.com/tutorials/video/Hunter%20tool%20usage.mp4

Re: Catches With A Hunter Tool

#8

Re: Catches With A Hunter Tool

steve worcester

It may be self feeding, which leads to the tool trying to take out too big of a chunk. Try the same cut with the lathe slowed down.

Re: Catches With A Hunter Tool

#9

Re: Catches With A Hunter Tool

Stuart Johnson

Thanks to everyone for the tips. John, either missed or forgot about the video you linked for me. You show exactly how to use the tool. With the video in mind I'll try your recommendation about using some scrap material. I'm pretty sure I was using the lower edge as a scraper and not rubbing the bevel when beginning a cut.

Re: Catches With A Hunter Tool

#10

Re: Catches With A Hunter Tool

Dinyar Chavda

Hi John:

Excellent video. I don't know if it is just my computer, but you turn into a chipmunk (at least from an auditory viewpoint) around 5:11 for about 30 seconds, and then your normal voice comes on. Has anyone else experienced this?

Re: Catches With A Hunter Tool

#11

Re: Catches With A Hunter Tool

Carol Reed

Yes, it did for me, too.

But then John can be a pretty intense guy!

Re: Catches With A Hunter Tool

#12

Re: Catches With A Hunter Tool

Fred Bearman

I thought it was just me - obviously not! I think the video sped up also. But that said, John does an excellent job with teaching this tool - even I understood.

Re: Catches With A Hunter Tool

#13

George Taylor

Re: Catches With A Hunter Tool

George Taylor

Same here, I tried from PC (Explorer) and Mac (Safari) so I would say it probably is not the hardware/system.

Alvin definitely has competition now from John! :D

George

Re: Catches With A Hunter Tool

#14

Re: Catches With A Hunter Tool

John Lucas

Well I'll have to take the time to watch it and see if it's something I can correct.