Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Need help - stuck Nova DVR Hand wheel

Posts

Need help - stuck Nova DVR Hand wheel

#1

Need help - stuck Nova DVR Hand wheel

Bill MacLachlan

Finally got my lathe back up and running after 16 months. Moved and had to build wife's sewing / knitting room and my shop first. Have turned a couple of things and found the handwheel / quill tougher to turn, so thought I would take apart and clean out.

Have removed the quill, set screw and keeper plate, but the handwheel ass'y will not come out. Turns freely and it will move about 1/8" to 3/16", but it feels like it bottoms out on something metal. I cannot find any hidden set screws or anything else. If I force it out, it will bind and lock in place. I have found a couple pieces of small gauge wire in the keeper plate groove.

Have tried to re-install quill and will only thread in 3-4 threads and binds tight. But will thread all the way through if I come in from the handwheel end.

I am lost at to what to do next.

Thanks for any help you can offer, Bill

Re: Need help - stuck Nova DVR Hand wheel

#2

Alan Zenreich

Re: Need help - stuck Nova DVR Hand wheel

Alan Zenreich

I don't recall... but is the handwheel a left handed thread? Are you sure you're not inadvertantly tightening the wheel?

Re: Need help - stuck Nova DVR Hand wheel

#3

Re: Need help - stuck Nova DVR Hand wheel

D. Hansen

if it is the handwheel on the left side you are referring to it is a left hand thread. Lock the drive and use one of those rubber thingy's to turn it "backwards". From your description though I guess you are referring to the tailstock. If so, there is a set screw that holds the lock piece in. It is just forward of the tailstock wheel. The right hand wheel is right hand thread. The manual suggests that the quill may have some sap or other matter holding it in. It says to gently tap the quill with a mallet.

Re: Need help - stuck Nova DVR Hand wheel

#4

Re: Need help - stuck Nova DVR Hand wheel

Bill MacLachlan

It is the tailstock handwheel I am having trouble with. I have removed the set screw, mounted at the 12:00 o'clock position, behind the handwheel. I have also removed the little locking shim. What I haven't done is use the quill to tap out the handwheel. I will try that in the morning and see if I can budge the handwheel assembly. It bothers me that I cannot thread the quill back into the handwheel assembly more than 3-4 threads.

Thanks,

Re: Need help - stuck Nova DVR Hand wheel

#5

Re: Need help - stuck Nova DVR Hand wheel

Barry Irby

I just took mine out the other day. If you have loosened the set screw and removed the palate, there is nothing else that is "supposed" to hold the hand wheel. It should slip right out. the only thing you said that confused me was the thing about the two small pieces of fine wire. I don't what they are or where they came from. Mine had gotten stiff and I had removed and cleaned and oiled the quill, but it did not help. When I removed the plate that runs in the race and holds the handwheel in I found crud in the race. Cleaned it out and reassembled it and its much smoother. I would suggest that your pieces of wire may be edges of pieces that have come off. Or maybe wire got in there some other way, but I am thinking there is more in there binding the handwheel. You might try flooding it with oil to see if you can float it out or try blowing it out with air pressure. Or go for brute force and just drive the handwheel out. You could put the quill back in and slide the tailstock up to the drive shaft and the turn the handwheel with the tailstock locked and it should drive itself out.

Re: Need help - stuck Nova DVR Hand wheel

#6

PS there is a pin....

Barry Irby

in the tailstock that keeps the quill from spinning. Could it be that the reason you can't screw the quill in any further is that you have run into the pin?

Re: Need help - stuck Nova DVR Hand wheel

#7

Re: PS there is a pin....

Bill_MacLachlan

Thanks Barry, the pin on the inboard end of the tailstock had caught me before. But I have been lining the slot in the quill up with it. So that shouldn't be a problem. I thought the set screw & key should be all there was. Will try the brute force tomorrow, but not sure that will work.

Re: Need help - stuck Nova DVR Hand wheel

#8

No Brute force yet

Jorge Casta�eda

I've been there, bur do not remember how it was the procedure. There is a hole somewhere and you put an Allen wrench in there, and then rotating until the set screw is in alignment, then you can remove the set screw and everything comes apart. Mine had big burs, maybe from the original machining, that had to be filed out . I'll go look when I ca a little later and will get back at yo. asap.

Re: Need help - stuck Nova DVR Hand wheel

#9

Brute force helped but not totally

Bill MacLachlan

I put the quill back in and mounted a block of wood in the chuck and rammed the quill against the block a few times. This did not loosen up the handwheel assembly, but for some stupid reason I can now thread the quill completely through the hand wheel. So partially fixed and operational.

But still cannot remove and clean the hand wheel. Also now have a problem that the little set screw that holds the keeper in place will not go all the way in and keep the keeper solid. Will see if I can find a 6mm set screw and tap at work tomorrow.

Stay tuned,

Re: Need help - stuck Nova DVR Hand wheel

#10

Got it out yet?

Jorge Casta�eda

Bill, I just disassembled my tail stock. ts

first, with the quill partially extended, remove the tightening knob, now cover the hole with one hand and turn the ts upside down, wiggle the quill until the key drops into your hand.

Now put it back the lathe bed and tighten it so stay put. on the extreme right, look into the wheel, more or less 180 degrees from the crank there is a hole, in that hole, position it so it is upper most, and wiggle it a little back and forth until the 3mm Allen key goes in and meets the set screw, back it as far as it will go, if you try to turn the wheel, the set screw prevents it so turn it in a couple turns until the wheel can rotate, now looking from the top, there is a slot and there is a key in that slot, I used a small scratch awl and lift the key up from the bottom, as soon as you take it out, back the wheel as far as it will go, it will come out completely, now just pull out the quill from the other end.

Clean crud and dress any burrs, a little grease and reassemble

Hope this helps.

Re: Need help - stuck Nova DVR Hand wheel

#11

Re: Got it out yet?

Bill MacLachlan

Jorge;

Never did get it out. I re-tapped the set screw hole and reassembled the quill & tailstock and it is freer now than it has been in a long time. So thought I would leave well enough alone.

Still not sure what was holding the handwheel assembly in place, but did disassemble like you suggested, but still stuck in place.

Thanks for all your help, Bill