Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

tool rest challenge

Posts

tool rest challenge

#1

tool rest challenge

Don McLeod

Jorge Castafieda said if you want tool rests, make your own. So I took Jorge up on the challenge and made three - a friend with a machine shop did the welding. One is a modified "S" , one a 15" curve and one a "J" shape. They are made out of 7/8" cold rolled steel and 1" CR steel post. Total cost (CDN) $41.00, $21.00 for 3 ft of 7/8" CR steel and 1ft of 1" CR steel, cost of bending and welding $20.00. Total working time 1 hour. I'll try and post a picture when I finish polishing them.

Re: tool rest challenge

#2

Steven Antonucci

beats me *LINK*

steven antonucci

I went to the local scrap yard and bought a 1" steel bar (about 48") for about $2. I already owned the modular tool rest in the lin below, so I just had to drill a hole and tap it, which took about 30 minutes at a friends house (I didn't have the right taps).

I could probably get 3-4 rests out of this bar. Bending it would be a workout...


Modular rest system (Note the post)

Re: tool rest challenge

#3

Re: tool rest challenge

Jorge Casta�eda

Don,

You made my day!, good way to start it reading your post.

Glad I did help to spread the word, thanks David Lancaster. He was the one that started it.

Re: tool rest challenge

#4

Re: tool rest challenge

Don McLeod

Jorge,

Thanks to your post, I made the plunge and found it was much easier to do and now wonder why I waited so long.

Re: tool rest challenge

#5

Lyle Jamieson

Re: tool rest challenge

Lyle Jamieson

For an alternative...cause I dont like the round tool rests, they push your support too far from your work with the handle down cuts like pull cuts or sheer scraping with a bowl gouge. Just weld a piece of flat steel on a 45 degree angle to the post. 1/4 or 5/16 by 2 by 9 is a perfect size. Now the top edge of the tool rest is close up to the wood no matter what cut you want to do. If you want a bent tool rest weld it verticle on the post after you bend it.

Re: tool rest challenge

#6

Re: tool rest challenge

Don McLeod

I agree the round ones leave something to desire but they do work , are quick to make and don't have the depth problems of rectangular stock. I made straight rests with hardened drill rod for their edge and they work great. My thought on the round ones was that they would be stiff enough to handle the forces at work at the outer extremity. I've had the opportunity to try them out and they work fine. After I finished making the round ones , I came across a commercial one made from 1/2" x 1 1/4" steel. which may be easier and safer to cold bend. I've posted pictures of the rests on another forum but haven't figured out how to post them herre.

Re: tool rest challenge

#7

Re: tool rest challenge

john lucas

I think it depends on the tools you use and how you use them. Many of the cuts I make while bowl turning require the tool to be over the rest quite a ways. That's assuming I use a straight rest and a curve bowl. Therefore the round rest works about as well as the flat rests.

My Thompson Detail gouge is quite thick. I grind away a fair amount of it on the bottom so I can reach into tight spaces. This requires that I move the tool rest back far enough to be on the flat of the bar. If I have the tool rest really close then the bevel is on the tool rest and that doesn't work. I found this out when I got my Robust Tool rest. I love the rest but often have the fulcrum point of that tool rest about as far as the center of a round tool rest.

I love to have the tool rest as close to the work as possible but I find that for much of the things that I turn there isn't a lot of difference between the round bars and the ones like the Robust. I still like my Robust tool rest better than all the others.

Re: tool rest challenge

#8

Re: tool rest challenge

Peter Hyde



These cost less than $40 as I had flat bar left over. 2 @ 12" ones are 1 1/4" x 1/2" 2 @ 14" are 1 1/2" x 1/2". Bending was done for free on a 3 wheel planetary bender approx. 18" radius

Re: tool rest challenge

#9

Re: tool rest challenge

Don McLeod

Nicely made.

Here's the ones Imade.

Re: tool rest challenge

#10

Re: tool rest challenge

Jorge Casta�eda

Peter,

Nice job!

Re: tool rest challenge

#11

Re: tool rest challenge

Jorge Casta�eda

Very nice Don, and when the need arise, you know the path. : D